language

HUATAO GROUP
News & Events

We Help Customers To Meet The Great Challenges Of Our Time.

VIEW PRODUCTS
scroll down

Back to Overview

Press felt for paper machines: selection and care guide

Nov 18,2026

Press felt for paper machines: selection and care guide

On an Indian paper machine the press felt is the piece of machine clothing that quietly decides how much steam the dryer section burns. It never touches the wire side of the sheet, yet it governs how much water is left to evaporate. After the forming section a web leaves the couch at roughly 18–22% solids on most packaging machines. The press section lifts that figure to somewhere in the high thirties or mid forties, and the felt is the porous belt that receives the water squeezed out in each nip. A press felt that has lost void volume does not announce itself with an alarm. Steam demand creeps up, the sheet shows crush marks, and the operator slows the machine a little to hold the reel moisture.

This guide is about the press felt on a paper machine as a working tool: how a wet press felt is built, what compaction, permeability (CFM) and caliper actually tell you, how felt tension and guiding interact, and how to condition a felt so it lasts. The examples come from conditions common in India: kraft, duplex and writing-printing machines running waste paper, bagasse or wheat straw, where monsoon humidity, hot process water, recirculated white water and hard make-up water each shorten felt life in their own way.

Press felt for paper machines

What a press felt does on a paper machine

The press felt has three jobs, and they pull against each other. It has to accept water from the sheet in the nip and carry it away, it has to support and smooth the sheet so the web is not marked or crushed, and it has to run stably without wandering, wrinkling or stretching unevenly. A felt that is excellent at the first job but has an open, rough surface will mark the sheet. A felt with a very fine, dense face gives a smooth sheet but may not accept water fast enough at higher nip loads.

Mechanically the felt is a conveyor: the web and felt are squeezed together between two rolls, water leaves the sheet and enters the felt, and on the exit side the felt expands again. This rewetting at the nip exit is a real limit: a felt that is saturated with water will give some of it back to the sheet. That is one reason the felt is dried out by a suction box straight after the nip, so that it enters the next nip with empty void volume.

How a paper machine press felt is built

Most paper machine press felts have two parts: a woven base fabric that gives strength, stability and the basic channel structure, and a layer of fine synthetic batt fibre needled into both faces of the base. The batt is normally polyamide (nylon). The base supplies tensile strength and the resistance to stretching; the batt supplies the surface the sheet sees and the fine pores that move water.

Base fabric and batt layers

The base (single, multi-layer or laminated; monofilament for open channels, multifilament for a tighter, finer structure) gives strength and void volume. More layers resist squashing better but make a heavier felt that dries out more slowly in the nip.

A fine batt on the sheet side gives a smooth, dense surface that spreads nip pressure evenly and does not mark light grades. A coarser batt on the machine side gives open drainage paths towards the suction box. The usual approach is a gradient: fine on top, coarser underneath, so water moves from small pores into larger ones and is not trapped. When this gradient is lost through compaction or filling, the felt feels "dead" in the nip even though its measured permeability can still look acceptable.

Closed and seam press felt constructions

A closed or endless felt is woven or joined into a continuous loop at the factory. It has no seam, so there is no seam mark and the dewatering profile is uniform across the whole length. The drawback is installation: the felt has to be slid onto the machine from the side, which means the machine frame must be able to open. Many older Indian machines have press frames that do not permit this without removing a roll or a section of the cantilever, so a closed felt is not always practical.

A seam press felt is delivered open with a loop on each end. It is pulled through the press section and joined on the machine with a pintle. This cuts crane time and manpower for a change and shortens the shutdown. The seam area must resist the nip, compaction and filling like the body of the felt; otherwise it wears into a groove and the sheet shows a mark once per felt revolution.

Close-up of press felt

Wet press felt, top felt and dryer felt: where each runs

Felts are classified by position, and the position determines what is asked of them.

Felt positionMain roleTypical design emphasisTypical failure to watch
Wet press felt (pick-up / first press)Remove water from a weak, wet web and carry it through the nipHigh void volume, good water handling, resilient to high nip loadsEarly compaction, sheet crushing, uneven dewatering across the width
Wet press felt (later presses)Remove remaining water and smooth the sheetFine face for smoothness, stable permeability across the runFilling with fines and sizing, loss of permeability
Top feltWorks above the sheet, guides and flattens the paperFine and even surface, good release of the sheetMarking from wear, sticking in humid conditions
Dryer feltHolds the sheet against steam-heated cylinders (see the separate dryer fabric guide)Permeability and heat-transfer behaviour, hydrolysis resistanceContamination, hydrolysis in high steam positions

Dense press felt: when a tighter structure helps

A dense press felt uses finer yarns and a tighter batt for a smoother, more uniform face. It suits printing and writing grades and the top ply of duplex board, but on heavy kraft liner at high nip load a structure that is too tight leaves the felt saturated and causes rewetting at the nip exit.

There is no universal answer. A dense structure helps when the nip is gentle and the sheet is light; an open structure with higher void volume helps when the sheet is heavy and the nip load is high. Choosing between them is the single most useful conversation to have with a felt supplier, and it should be based on basis weight, nip load, press configuration and the furnish.

Press felt compaction: what happens and why it matters

Compaction is the permanent loss of thickness and void volume under repeated nip loading. Every pass through the nip squeezes the felt; most of the thickness returns as the felt leaves the nip, but a little does not. Over days and weeks the batt flattens, the base yarns settle, and the felt becomes thinner and denser. The effect is a loss of water-holding space: the felt reaches saturation sooner, so water has nowhere to go and the sheet leaves the press wetter.

Compaction versus filling. If permeability has fallen but the caliper has barely changed, the felt is mostly filled and a good conditioning programme can recover much of it. If caliper has fallen and permeability has fallen with it, the structure itself has collapsed. Cleaning will tidy the surface but it will not bring the felt back. Measuring both numbers on a retired felt tells you which problem you actually had.

Press felt CFM and permeability: reading the number correctly

Permeability is measured as the volume of air that passes through a unit area of felt at a standard pressure difference. In the paper industry the number is usually stated in cubic feet per minute per square foot, shortened to CFM, with a test pressure fixed by the method. Higher CFM means a more open felt. A new press felt may be in the range of a few tens of CFM up to well over one hundred, depending on the grade it is made for, the position on the press, and the type of base fabric.

Three points about permeability are easy to get wrong.

  1. Air permeability is not water permeability. A felt with a clean air reading can still drain poorly if the pores are small and wet with fines. Air goes through a dry felt; water has to get through a wet, loaded one. Treat CFM as an indicator, not as a guarantee.
  2. New-felt CFM and in-service CFM are different tools. The new-felt number defines the structure you ordered. The in-service trend defines how fast the felt is filling. A fall of more than a third in a short time is a warning sign worth checking.
  3. Higher is not better. A very open felt dewaters quickly at first but can leave a marked, rough sheet and may not offer enough contact area at the nip. The best number is the one matched to the grade and the nip.

Press felt caliper and void volume

Caliper is the felt thickness under a defined load, and it is the nearest simple measure of void volume, since most water storage sits in the thickness. A new felt on a packaging machine is typically a few millimetres thick. The useful figure is the rate of fall. Measure when new, then after one week, two weeks and monthly. A smooth downward curve is normal; a sudden step usually means a mechanical event such as a wrinkle or a sheet pile-up in the nip; a flat curve with worsening dewatering means filling rather than compaction.

Few mills measure caliper because it needs a gauge and a stopped felt. A simple version is a thickness gauge at the felt edge during each shutdown, on spots marked with a paint pen and logged by day. Within a month the data shows whether the felt will reach its planned life.

Typical industry reference values for wet press felts

Fibre in batt layersPolyamide (nylon), fine on sheet side
Base fabricWoven single or multi-layer, or laminated
Air permeability (new felt)Tens of CFM to above 100, grade dependent
New-felt thicknessA few millimetres, depending on layers and batt weight
Felt tensionLower than forming fabric; set to supplier guidance
Service lifeWeeks to a few months, by position, load and cleanliness
Seam optionsEndless (closed) or on-machine seam with pintle

These are generic figures that vary with press type and grade. They are for sanity-checking a datasheet, not for ordering from; the final specification must come from the felt maker with nip load, speed, sheet weight and furnish known.

Press felt tension, guiding and stretching

A press felt is run at a much lower tension than a forming fabric or a dryer fabric. The tension has to be high enough that the felt does not wrinkle or slip in the nips and low enough that it does not stretch the base and speed up compaction. Too much tension has the same effect as excessive nip load: it squeezes the structure and shortens felt life. Too little tension causes slackness, wrinkles and creasing in the nip, and in extreme cases the sheet is carried off with the felt.

The right setting is given by the felt supplier for the specific construction, and the mill should log the tension used at the start of life and at each cleaning stop. Many mills find that tension drifts upwards as the felt stretches, then drifts downwards after a long shutdown when the felt relaxes. The tension gauge at the stretcher or the stretch roll position is the simplest early indicator.

Felt guiding

The felt wanders sideways as it runs, and a corrector has to bring it back. A pneumatic bellows corrector moves a guide roll in small steps in response to a sensor at the felt edge. If it is too slow the felt creeps to one side, and if it is too aggressive it hunts and puts a diagonal stress through the structure. On paper machines the guide system that holds the felt in position is as important as the felt itself, and the guide roll bearings, the sensor and the air supply all need to be maintained. Poor guiding produces one-sided wear, a "frayed" edge, and a moisture profile that is wet on one side.

Felt stretchers and tensioners also matter here. They keep the felt tight as it stretches in service, and they allow the felt to be released for changing. The felt stretcher and tensioner range is described on the felt stretcher and tensioner page; the pneumatic correctors suit forming wire, press felt and dryer fabric alike.

Press felt cleaning and conditioning

Conditioning is everything done while the machine is running to keep the felt open: high-pressure needle showers, low-pressure lubrication showers, the felt suction box, and chemical cleaning when the need is clear. It is the part of felt care that depends most on the mill, and it is where felts are most often shortened.

Showers

The most common arrangement is a high-pressure oscillating needle shower on the return run, set up to cut the contamination off the felt surface, and a low-pressure shower that flushes the loosened material off before the suction box. The high-pressure shower must oscillate, because a fixed jet cuts a line into the batt. Nozzle blockage is a regular issue on Indian machines using recirculated water, so a filtered clean supply is better than raw white water. A single blocked nozzle leaves a streak of dirty felt and a corresponding moisture streak in the sheet.

The shower system quality changes felt life, downtime and cleaning consumption. Spray pipes and nozzles installed for felt conditioning, clothing cleaning and roll cleaning are part of the same equipment family, and their design affects paper quality directly. Huatao supplies spray shower and nozzle systems; the spray shower page lists the types.

Felt suction box

The felt suction box sits on the felt return run and pulls water out of the felt after the nip, so the felt enters the next nip with empty void volume. A suction box with a smooth, hard, low-friction cover and an adjustable slot width helps the felt both to dry and to last, since a rough cover wears the felt. The single-chamber and two-chamber types give stable vacuum, and the slot can be set for the machine speed and grade. A worn or misaligned suction box takes away felt life that no chemical programme can give back, so inspect its cover at every felt change. See the felt suction box page for the construction.

Chemical cleaning

Chemical cleaning is a controlled intervention, not a routine. The type of deposit decides the chemistry. Organic deposits such as pitch, stickies, starch and sizing respond to alkaline or surfactant-based cleaners; mineral scale such as calcium carbonate responds to acid. Using the wrong one makes things worse. Acid on an organic deposit can fix it, and alkali on scale does nothing. If the deposit is not known, a simple lab test on a felt sample cut from a retired felt will show whether it dissolves in acid or in alkali.

Clean at a planned stop, not after the clogging is severe. Rinse long with clean water, because leftover chemical reappears as foaming or sticking. Log permeability before and after each clean; if recovery shrinks every time, the felt is near the end.

Press felts on Indian paper machines: steam, furnish and climate

On most Indian packaging machines the steam that heats the dryer cylinders is the largest energy load, and the press section decides how much of it is needed. Every extra point of solids leaving the press means less water for the dryer. As a working rule, one percentage point of press solids reduces dryer steam demand by roughly four to five percent; the exact figure varies by machine, but the direction does not. In many Indian mills boiler capacity is fixed by the coal, rice husk or bagasse supply, so there is no steam in reserve. When the felt drifts from good to poor across its run, the operator cannot raise steam pressure and slows the machine instead. The lost output is the real penalty of a felt past its best.

Which Indian machines run press felts hardest

The typical Indian press section is a plain or suction press pair on a Fourdrinier, or a cylinder-mould machine, making kraft, fluting, duplex or writing-printing paper at low to medium speed, often behind an open headbox. Many are older machines that have been rebuilt and sped up in stages. Press loads were not always raised with the speed, so the felt carries a wet sheet through a nip that was never designed for it. On such machines the felt is often the only thing that can be changed quickly to claw back dryness. Mills in Gujarat, Maharashtra, Punjab, Uttar Pradesh and Tamil Nadu that run heavy waste-paper grades also push more contamination into the felt than mills on cleaner pulp.

Indian furnish: OCC, bagasse and wheat straw

  • Mixed waste paper and OCC. Stickies, wax and coating residue pass the screens and settle in the felt. Expect filling and the need for alkaline cleaning.
  • Bagasse pulp. Pith fines and silica-bearing particles fill the felt and abrade the face. Frequent shower oscillation matters more than strong chemicals.
  • Wheat straw pulp. Very fine, slow-draining stock puts a heavy water load on the first press and tends to blind the felt surface early.

Indian climate and water

Pre-monsoon summer heat softens the batt, so compaction runs faster and the felt loses permeability sooner than in winter. During the monsoon, humid air slows evaporation and the dryer has less margin. Many mills close their water loops to cut fresh water use, which also recirculates fines, starch and dissolved salts into the felt, and hard make-up water leaves calcium carbonate scale in the felt and the suction box slot. That scale needs an acid step in the cleaning routine that mills on soft water never see.

A practical India-specific habit. Log reel moisture and felt permeability by season. A felt that gave eight weeks in winter may give much less in May; planning felt changes around the pre-monsoon heat and the humid weeks that follow avoids a forced stop in the worst conditions.

How to select a press felt for your machine

A felt supplier needs a handful of facts to recommend a design, and a mill that has them ready gets a better answer. The table sets out the inputs and why each one counts.

Input to supplierWhy it matters
Paper grade and basis weight rangeSets how much water must be removed and how fine the face must be
Machine speed and trim widthSets the time in the nip and the water-handling rate
Press configuration (plain, suction, grooved, shoe)Decides whether the felt needs a coarse, open structure or a fine one
Maximum nip load and roll crownDrives compaction resistance and edge behaviour
Furnish (OCC, mixed waste, bagasse, wheat straw, virgin fibre)Determines the fines and contaminants that will fill the felt
Water quality and temperatureDecides the cleaning regime and the risk of scale
Access for installation (frame open or closed)Decides whether an endless or a seam felt is possible
Life achieved and failure mode on the last feltThe most useful guide; shows what to change

Keep a short record per press position: time of fitting, tension, permeability, caliper, reel moisture and reason for removal. Three felt changes of such records tell a mill more about its press section than any datasheet.

Common press felt problems and their causes

SymptomLikely causeWhat to check
Sheet leaves the press wetter than beforeCompaction or filling, worn suction box cover, shower faultPermeability trend, caliper, suction box vacuum and cover
Moisture streak in the machine directionBlocked shower nozzle, localised filling, uneven roll crownNozzle pattern, permeability profile across width
Crush marks or wet streaks in the sheetExcessive nip load on a compacted felt, wrinkleNip load, tension, guide roll alignment
Once-per-revolution markSeam wear, contaminated spot, damaged areaSeam condition, felt surface inspection
Felt edge frayed or one side wornPoor guiding, misaligned rollsCorrector response, sensor, bearings
Rapid permeability loss after start-upNo break-in, high initial load, hot felt, contaminated waterStart-up procedure, water quality, shower pressure
Foaming or sticking after cleaningChemical left in the feltRinse time, rinse water quality
Wrinkles in the nipLow tension, uneven stretching, guide faultTension log, stretcher, guide roll

Breaking in a new felt

Check that rolls are clean and free of sharp edges, and that guide, stretcher and showers work. Start at reduced nip load and raise it over the first several hours. Record starting tension, permeability and reel moisture after a stable hour; every later reading is compared with these.

Huatao Group press felt for Indian paper machines

Huatao Group supplies press felts for paper and board machines, next to its forming fabrics and dryer fabrics. Its press felt range is organised by position: wet felt, top felt and dryer felt. The wet felt presses the raw paper to dehydrate it and smooth the surface; the top felt runs above the wet felt, guiding and flattening the paper; the dryer felt wraps the dryer cylinder to iron and dry the paper. The product is built around three functions: water removal, smoothing and runnability. What follows ties each stated feature to the Indian machine it matters for.

Press felt features and where they matter in India

High dehydration rate, high anti-compaction capacitySteam-limited kraft, fluting and duplex machines, and hot pre-monsoon months when felts compact fastest
Smooth, compact surface; very high elasticity and recoverabilityRebuilt older presses with uneven nip loading, and writing-printing grades where marking shows
Easy to keep clean; no stickiness, no uneven cloggingWaste-paper and OCC furnish with stickies and wax; bagasse and straw fines
Low total energy consumption, strong drainability, larger void volumeMills with fixed boiler capacity that cannot raise dryer steam when the sheet arrives wet
Long-lasting wear resistance and plastic strengthAbrasive agro-residue pulps and long continuous runs
Even pressure distribution from a smooth felt faceLow and medium speed machines whose crowned rolls give uneven nip load across the width

The knowledge base gives no numerical permeability or thickness figure for the Huatao range, so the values given earlier in this guide remain industry reference values only.

Seam press felt for Indian press frames

Huatao also lists a seam press felt, joined on the machine. Its listed features: easy to seam on the machine; safe, easy and quick installation that reduces manpower and crane time; increased efficiency of shutdown time; a durable structure with a strong, non-marking seam area; good resistance to compaction and filling; and good water handling capacity. For Indian machines whose press frames do not open easily, or mills with limited crane access, installation without sliding a closed loop sideways is the practical point, and a shorter stop matters when every hour of lost output counts.

Around the felt, Huatao also supplies felt stretchers and tensioners, with pneumatic correctors for forming wire, press felt and dryer fabric, and spray showers for felt conditioning. Felt design is made to the customer's machine and operating data.

Frequently asked questions

What is the difference between a press felt and a forming fabric?
A forming fabric (the wire) sits in the forming section and drains water from a very dilute stock, about 99% water, through gravity and suction, and it carries the sheet while it forms. A press felt sits in the press section, after the sheet has been formed, and receives water squeezed out of an already formed web in the nip. The forming fabric is a woven plastic mesh without batt, run at high tension. The press felt is a woven base needled with fine batt fibre and run at lower tension. They also fail differently: wires wear and stretch, while felts compact and fill. For a closer look at the wire, see the forming fabric guide.
How do I know when a press felt needs to be replaced?
Look at the trend, not a single number. A felt is at the end of its life when permeability has dropped and cleaning no longer brings it back, caliper has fallen to the point that void volume is limited, reel moisture has crept up despite normal nip load, or marks appear that were not there earlier. Mills that log permeability, caliper and reel moisture weekly can usually see the decision coming a few weeks in advance and schedule the change for a planned stop, rather than waiting for a forced one. A felt that is physically damaged, with a hole, torn seam or heavy edge wear, should be changed immediately.
Can a compacted press felt be restored by cleaning?
Only partly. Cleaning removes contamination that sits in the pores, so it recovers permeability lost to filling. It cannot restore thickness lost to compaction, because that is a permanent change of structure in the batt and base. Check by comparing caliper with its starting value: if caliper is close to the starting figure and permeability is low, cleaning has a good chance. If caliper has fallen a lot, cleaning will give a small and short-lived gain. Frequent mild conditioning during running is much more effective than a heavy clean at the end of a felt's life.
Is a higher CFM always better for a press felt?
No. A higher CFM means a more open structure, which takes water quickly, but it also means a coarser face and fewer contact points in the nip. On a heavy kraft liner at high nip load a more open felt is usually right. On a printing and writing grade it can leave a marked sheet. The right number is the one that suits the grade, the press position and the load. When comparing two felts, compare them at the same measurement method and the same pressure drop, since CFM values tested under different conditions are not directly comparable.
When should I choose a seam press felt over a closed one?
Choose a seam felt when the press frame cannot be opened easily or when crane time and manpower are limited. The felt is pulled through the press section and joined on the machine, so a change takes less time. Choose a closed felt where the frame allows side access and the sheet is sensitive to marking, because there is no seam to mark the sheet. Many older Indian machines have press sections where side access is awkward, so a seam felt is often the practical option in India. A well-made seam is flexible, non-marking, and resists compaction like the rest of the felt.
How often should a press felt be cleaned in Indian summer conditions?
Continuous conditioning with showers and the suction box runs all the time the machine runs, and that is the main cleaning. Chemical cleaning is added when the permeability trend shows that filling is outpacing what the showers remove, usually at planned stops. Many mills clean at intervals of a few weeks, but the right interval depends on furnish, water quality and position. A mill on clean virgin pulp may need it rarely, while a mill on mixed waste paper with sticky contaminants may need it more often. In hot Indian summers with hard water, scale and faster compaction shorten the interval. Use the permeability log, not the calendar, to decide.
Why does a felt that looks clean still dewater poorly on a bagasse or waste-paper machine in India?
A clean-looking surface tells you little. On Indian mills using bagasse or waste paper, pith fines, filler, stickies and sizing lodge deep in the pores and in the base fabric, out of sight from the surface. The felt can also be compacted, which cannot be seen at all. Check permeability across the width, measure caliper, and look at the suction box vacuum and cover, since a worn cover or a vacuum leak leaves water in the felt. A hot, glazed surface under raking light, or a felt that feels hard and flat to the hand, is also a sign of lost resilience.
How does press felt condition affect dryer steam consumption?
The dryer evaporates whatever water the press leaves in the sheet. A better felt means higher solids after the press, so less water for the dryer to remove. As a working rule, a gain of one percentage point in press solids lowers dryer steam demand by roughly four to five percent, though the exact figure depends on the machine. On steam-limited Indian machines, especially in the humid monsoon weeks, the effect shows up as machine speed rather than a steam reading: if the felt is poor, the operator has to slow down to keep the reel dry. Tracking reel moisture against felt age shows the link clearly.