language

HUATAO GROUP
News & Events

We Help Customers To Meet The Great Challenges Of Our Time.

VIEW PRODUCTS
scroll down

Back to Overview

Pressure screen in paper industry: types and selection

Nov 18,2026

Pressure screen in paper industry: types and selection

A pressure screen decides, slot by slot, which fibre goes on to the paper machine and which is sent back. In every pressure screen in the paper industry the principle is the same: pulp is pumped into a closed housing, a rotor sweeps a slotted or perforated basket, good fibre passes through, and shives, plastic flakes, bark and sticky lumps are held back as reject. What changes between machines is the side of the basket the stock enters, how reject leaves, and the consistency the screen is built for. For an Indian mill running waste paper, straw or bagasse, that choice shows up directly as basket life, specks in the sheet and the size of the water circuit.

This guide explains how an inflow pressure screen, an upflow pressure screen and a mid consistency pressure screen differ, what the slotted basket and the rotor actually do, how to read a pressure-drop trend, and where a pre-net screen in front of the headbox differs from a coarse screen behind the pulper. The second half turns to India: OCC and mixed waste lines in Gujarat and Maharashtra, bagasse and wheat straw lines in Uttar Pradesh and Punjab, and what monsoon humidity and summer heat do to screening. Pulpers and cleaners get a sentence and a link only; they have their own guides.

Pressure screen

What a pressure screen does in the paper industry

Screening separates by size and shape; cleaners separate by density. A softwood fibre is about 3 mm long and 30 micrometres wide and passes a 0.25 mm slot if it travels with the flow. A 5 mm flake of plastic film, a wet-strength paper chip that never fully disintegrated, or a clump of fibre glued by a sticky will not. Everything else on the machine exists to keep that simple principle working for months without the basket blinding.

In a waste paper line the pressure screen is a chain. A coarse screen with holes of roughly 1.5 to 3 mm follows the pulper and protects everything downstream. A fine screen with narrow slots comes after a cleaning stage and removes the shives, stickies and plastic fragments that survive. Tailings pass to a secondary screen or a reject separator so fibre is recovered before reject leaves. Finally a pre-net screen, also called a head box pressure screen, polices the stock just ahead of the fan pump and headbox.

Flow through the basket is driven by a small differential, usually well under one bar, which is why these machines are called pressure screens and not gravity screens. Judge any screen on four things: removal efficiency for a given contaminant size, reject rate (a screen that throws away good fibre to protect the sheet gains nothing), pulsation passed to the accepted stock, and capacity before pressure drop climbs. The three main types are different compromises between them.

Inflow pressure screen

How basket, rotor and flow work together

Stock fills the annular space on the feed side of the basket and a thin layer is pushed through the slots. Left alone, fibre and contaminants would mat the surface and blind the slots within seconds. The rotor prevents that: each foil or bump passing the basket creates a short negative pulse behind it, pulling a little stock back through the slots and lifting the mat. The pulse repeats many tens of times per second at every slot.

Contaminants that cannot pass are carried along the basket to the reject outlet. Fine screens commonly run at a volumetric reject rate of 10 to 30 per cent. That sounds high but is normal; the rate must be high enough to stop contaminants thickening and plugging the outlet. Lowering it to recover fibre works until the day the reject line plugs, and then it fails abruptly.

Thickening, the quiet failure mode: Accepts leave through the slots, so consistency rises along the basket. With too little reject flow the stock near the outlet becomes a plug and differential pressure shoots up. When a screen runs fine for a week and then trips on high differential, check reject flow and dilution water before blaming the basket.

Flow direction and why names mislead

Suppliers use "inflow", "outflow" and "upflow" loosely, which causes trouble on purchase specifications. In an inside-fed design stock enters inside the basket and accepts pass outwards; in an outside-fed design stock enters outside and accepts pass inwards. The rotor always sits on the feed side. Confirm the flow direction from the drawing; a rotor made for one arrangement does not fit the other.

Inflow, upflow and mid-consistency pressure screens compared

TypeTypical feed consistencyTypical useMain strengthMain limitation
Inflow pressure screenAbout 0.8 to 1.5%Fine screening of wood, straw and waste paper pulp; net filter before the paper machineLow pulsation, good homogenisation of acceptsBlinds quickly if the feed is dirty
Upflow pressure screenAbout 0.8 to 2.5%Coarse and fine screening of waste paper stockHeavy rejects leave from the bottom, light from the top; less abrasion on rotor and basketTwo reject paths to manage; taller footprint
Mid-consistency pressure screen2.5 to 4%Coarse and fine screening of waste paper stockSmaller water circuit, lower system energyThicker stock; seal water and discharge need attention
Pre-net (head box) screenLow, matched to approach flowLast screen before the paper machineFast pulse decay, protects the slice from lumpsNot a coarse screen; overloaded by poorly cleaned stock

Ranges are general industry practice; the 2.5 to 4 per cent band for the mid-consistency type also matches the range stated for Huatao's design. Furnish and basket design move the others in either direction.

Inflow pressure screen

This is what most mills mean by "the pressure screen". It is built for fine screening and its defining quality is low pulsation: rotor pulses are damped in the housing and accepts leave through a wide outlet, so the stream reaching the fan pump is smooth. Its weakness is sensitivity to feed. If coarse screening or cleaning upstream lets too much plastic or sticky through, the fine basket blinds and differential rises. That is a symptom of the stage before it; look back along the line, not forward.

Upflow pressure screen

Stock enters from the bottom. Staples, sand and small metal that survive the pulper and cleaners drop out and leave at the bottom; foam and film collect near the top and leave there. Neither contaminant is dragged the length of the basket with rotor foils chasing it, which is one of the quicker ways to destroy both parts. Mixed waste paper in India carries more metal and grit than most mills would like, so this layout suits the coarse stage.

Mid-consistency pressure screen

Working at 2.5 to 4 per cent, the mid consistency pressure screen needs less dilution water between pulper and screen, so pumps and pipes are smaller and system energy falls. The trade-off is mechanical: thick stock is harder to push through slots, the rotor must clear the basket without wrapping stringy material, and seal water must never be interrupted. Thick-stock machines have fewer margins, which is why seal-water alarms, interlocks and heavy-impurity discharge are standard on this type.

Slotted pressure screen baskets: slots, holes and wear

The basket does the separating. Round holes, roughly 1.5 to 3 mm, suit coarse screening. A slotted pressure screen basket, with slots commonly about 0.10 to 0.35 mm, suits fine screening because slot width controls the smallest dimension of a particle: a flat flake or fibre bundle that would slip through a round hole is stopped. The drawback is smaller open area and more sensitivity to blinding, so slotted baskets need a well-prepared feed.

Baskets are either machined, with slots cut through a solid wall, or assembled from profile wires so the slot widens in the flow direction and particles do not wedge. Surface condition and slot-width uniformity decide efficiency more than the nominal figure. Stainless steel is the usual material: standard austenitic grades for neutral to mildly acidic waste paper systems, a molybdenum-bearing grade where chlorides build up in a closed water circuit.

Symptom at the screenLikely causeWhat to check first
Differential pressure climbing over daysSlots partly blinded, or reject rate set too lowReject flow and dilution; compare with the clean-basket value
Differential jumping suddenlyReject line partly plugged, or heavy contaminants at the dischargeReject valve, heavy-impurity trap, discharge pipe
More shives or specks in the sheetWorn or damaged basket, leak at basket endsSlot widening, cracks, end seals
Pressure pulses at the headboxWorn rotor foils or loose rotorRotor condition, balance, clearance to basket
Vibration at the bearing housingRotor imbalance from wear or fibre build-up, bearing wearRotor balance and bearing temperature before opening
Good fibre in the rejectReject rate too high, tailing stage underperformingReject consistency and the secondary screen

Rotor for pressure screen: foils, bumps and clearance

The rotor for a pressure screen creates the backflush pulse, moves stock and reject along the basket, and holds a controlled gap to the basket so the stock layer stays thin. If wear opens the gap, the pulse weakens and the basket blinds; if a bent shaft closes it, rotor meets basket.

Foil rotors have a hydrofoil profile and give a sharp, short pulse, which is why they are preferred for fine screening; bump rotors give broader, gentler pulses. Foil tip speeds of roughly 15 to 25 m/s are typical, depending on design and consistency. Leading edges wear first, so the usual sign is a slow rise in differential and reject rate rather than a failure anyone can point to.

At each basket change, record the rotor-to-basket clearance on the new pair as a baseline, check foil edges for rounding and the foil welds for cracks, and check balance. A rotor that has lost metal unevenly shakes the bearings long before it fails visibly. Where the original maker of an older Indian screen can no longer supply parts, a rotor made to the existing drawing is the practical route.

Change the pair: Fitting a new basket against a worn rotor is a common shortcut and almost always shortens the new basket's life, because the clearance is wrong and the backflush weak. If the shutdown window allows only one job, at least measure the rotor against its original profile.

Pressure drop, reject rate and consistency in practice

The difference between feed and accepts pressure is the pressure drop across the basket, and it is the best single indicator of internal condition. On a clean basket at normal throughput it is typically a few tenths of a bar. What matters is the movement from the commissioning baseline, not the absolute number, so record the first week's readings. Most mills set an alarm and an operating limit and clean or change the basket before reaching it.

Reject rate is set by the reject valve. In waste paper plants the reject of a primary screen goes to a secondary, then to a tertiary or a reject separator, which uses a specially shaped rotor and backwash water to relieve fibre from tailings before final reject leaves as solid waste. A self-cleaning vibrating screen is the mechanical alternative for tailings, chosen according to available space and water balance.

Dilution should use clean white water, not fresh water in quantity. A common fault is to raise dilution to suppress rising differential. That treats the symptom, wastes water and hides a blinding basket that should have been cleaned.

Pre-net screen and head box pressure screen

The pre-net screen sits at the approach to the paper machine and is the last place a lump, sticky or plastic chip can be stopped before the slice. Here capacity is secondary. The first requirement is steady, low-pulse flow, because a pulse made at the screen travels to the headbox and appears as periodic basis-weight variation. If its frequency lands near a natural frequency of the approach piping, the sheet shows regular light and heavy bands. The remedy is to check the screen rotor, pulse damping and fan pump stability, not to adjust the headbox.

On many Indian machines with an open headbox, running kraft and writing grades at moderate speed, the pre-net screen is the only fine screening between cleaning and the slice, so it carries more responsibility than one stage in a multi-stage high-speed system. How stock is then delivered to the wire is covered in the guide to the open headbox, and the wire that receives it in the forming fabric guide.

Pressure screens in Indian waste paper, straw and bagasse mills

Indian stock-preparation lines are shaped by furnish and by machine age. Many mills run Fourdrinier or cylinder-mould machines, some decades old, making kraft, duplex board, writing and printing, and fluting at low to medium speed. Screens on such lines often feed an open headbox, so smooth flow from the pre-net screen matters more than peak capacity.

Waste paper and OCC lines in Gujarat, Maharashtra and Tamil Nadu

Mills making recycled packaging grades receive domestic OCC and mixed waste with plastic film, wax coatings, strapping, hot-melt adhesive, staples and grit. Bale quality varies from lot to lot, so the screening line must tolerate swings. A typical sequence is a coarse stage with an upflow or mid-consistency screen, a cleaner stage, fine slotted screens and a pre-net screen. The coarse stage must be tough: one metal fragment reaching a fine basket means a damaged basket and an unplanned stop. For where contaminants originate, see the hydrapulper guide and the page on cleaning equipment.

Bagasse and wheat straw lines in Uttar Pradesh, Punjab and Haryana

Mills pulping agricultural residue face a different problem. Bagasse and straw give short fibre with many fines, pith and dust. Pith in bagasse pulp blinds a fine basket fast if an earlier stage has not removed it, and straw leaves silica-bearing fines that wear baskets and rotor edges. These lines usually screen at lower consistency, with slot width and reject rate set for the high fines content. Seasonal feedstock also changes: bagasse arrives in the crushing season and is stored, so pith and moisture vary through the year and screen settings that suited November may not suit June.

Monsoon, heat and water: Indian shop-floor problems

Summer heat raises stock temperature, which thins stickies and lets them smear and pass fine slots, then re-agglomerate downstream. Monsoon brings damp bales and extra grit and mud in waste paper and wet bagasse with more pith to remove. Many Indian mills also run with limited fresh water and a tight effluent system. That pushes the decision towards equipment that shrinks the water circuit, and the mid-consistency screen at 2.5 to 4 per cent does that. For a mill whose pumps and pipes are already near capacity, it can be the deciding factor, provided operators are comfortable with seal-water and interlock systems.

For a line that already screens well at low consistency, there is no reason to change merely because a newer concept exists. Let the water balance and contaminant profile decide.

How to choose a pressure screen for an Indian stock preparation line

Start with the job, not the type: where the screen sits, which contaminants it must remove, what feed consistency is realistic, and what the accepts feed.

Typical industry reference values for pressure screen selection

Coarse screening basket openingsHoles of about 1.5 to 3 mm
Fine screening basket openingsSlots of about 0.10 to 0.35 mm
Feed consistency, fine stageAbout 0.8 to 1.5%
Feed consistency, mid-consistency typeAbout 2.5 to 4%
Pressure drop, clean basketA few tenths of a bar
Volumetric reject rate, fine stageCommonly 10 to 30%
Rotor tip speed, foil typeRoughly 15 to 25 m/s
Usual wetted materialAustenitic stainless steel (304, 316, 316L)

These ranges orient a discussion with a supplier; they are not the specification of any particular machine.

If the furnish is well-prepared recycled stock, pulse and final cleanliness dominate and an inflow design fits. If it is dirty OCC with metal and grit, the coarse stage is critical and an upflow screen suits. If water is the bottleneck, as in many inland and drought-prone Indian locations, look at mid-consistency. If the problem is large debris, holes may do; if the sheet shows small specks, slots are needed, though a narrower slot is not always better because it brings higher differential and faster blinding. A fine machine on a coarse stage wears out baskets, and a coarse machine as final screen leaves the sheet exposed. Finally confirm connection sizes, drive arrangement, seal-water supply and reject line position against the space available in the existing building.

Check upstream first: When an Indian mill reports specks, the instinct is to tighten the final screen. Often the better move is to inspect the pulper rotor and screen plate and the cleaner cones, because contaminants broken into small pieces upstream are far harder to remove than intact ones.

Maintenance, basket cleaning and troubleshooting

Each shift, log feed, accepts and reject pressure, motor current and reject flow, compare differential with the benchmark, listen at the bearing housing and feel for temperature rise. On mid-consistency machines confirm seal-water flow and test the alarm. An automatic oil injection device still needs its reservoir checked.

Inspection intervals depend on furnish: a fine screen on clean stock may run many months, a coarse screen on metal-laden OCC may need a look every few weeks. Rinse the basket, check slot edges in good light and gauge slot widths at several positions. If the basket is blinded rather than worn, high-pressure water along the slots, not across them, clears most fibre. Chemical cleaning suits stickies and wax, following the basket supplier's guidance. Never scrape slots with a hard tool; a scratch becomes a leak path. A slowly rising differential on a long-serving basket usually means worn slots, and cleaning will not restore it. A sudden differential drop with more specks means a broken basket or leaking seal, which is an immediate stop. Keep a spare basket and rotor for each screen size in service, and note drawing numbers while the machine runs well.

Huatao Group pressure screens for Indian stock preparation lines

Huatao Group, in Shijiazhuang, China, supplies the four screens covered here, plus related tailing equipment. What follows is limited to features the company lists for each, and what each means on Indian lines.

Inflow pressure screen: features and Indian use

Huatao lists it for fine screening of wood pulp, straw pulp and waste paper pulp, especially as the net filter before the paper machine. That covers the three furnish families in this article: an OCC mill in Gujarat, a wheat-straw mill in Punjab and a mixed-fibre mill in Tamil Nadu can specify the same machine family. Listed features and their meaning:

  • Inflow structure with low pulse and good homogenising effect: a smoother approach flow for the open-headbox machines common in India.
  • Companion-flange pulp outlet without gaskets, polished inner wall, seamless pipeline connection with no fibre hitching: fewer places for stringy bagasse and straw fibre to hang up and shed lumps later.
  • Small motor power, high capacity, low energy use: relevant where power supply and plant capacity limit what a line can add.
  • Long residence time, sufficient fibre relief, low fine-fibre loss: matters for straw and bagasse, where fines are already high.
  • Convenient disassembly and assembly, simple operation, fewer malfunctions in continuous work: suits mills where one fitter covers several machines.

Upflow pressure screen: features and Indian use

Listed for coarse and fine screening of waste paper pulp in stock preparation. Stock enters from the bottom, heavy impurities leave at the bottom and light ones at the top, shortening dwell time of impurities in the screening area and reducing wear on rotor and basket, which extends their service life. For Indian recycled lines fed with grit- and staple-laden OCC, that is the design logic aimed at the abrasion problem described earlier.

Mid-consistency pressure screen: features and Indian use

Listed for coarse and fine screening of various waste paper pulps, normally at 2.5 to 4 per cent consistency, with less water circulation and lower system energy. Other listed features:

  • Multi-blade rotor, no winding, efficient and low energy use: stringy plastic and fibre are common in Indian waste paper.
  • Heavy-impurity discharge pipe to keep the basket safe: protects against grit and metal in mixed bales.
  • Less fibre loss, sturdy and durable, convenient disassembly and assembly.
  • Automatic oil injection to reduce maintenance, seal-water flow automatic detection alarm, and an interlock system for equipment life: useful for mills with limited maintenance staff, and for lines where seal water can fail in summer shortages.

Pre-net screen

Listed for screening low-consistency pulp before the paper machine, removing impurities and breaking up pulp material to improve paper quality. The upside-down core structure keeps stock speed through the slots steady; a wide accepted outlet makes pulse decrease quickly; heavy particles flow in the outer area so the screen does not block; capacity is high and energy low. On slow Indian kraft and writing machines with an open headbox, that low-pulse behaviour is what the sheet needs.

Screen baskets, rotors and related separators

Huatao lists a screen basket and rotor range, including a rotor for inflow or outer pressure screens, in SUS304, SUS316 or SUS316L, with rotors made to a customer's drawing. Standard stainless grades suit neutral waste paper circuits, while 316L is the option for chloride-rich closed circuits; drawing-based manufacture helps with older Indian machines whose original supplier no longer provides parts. For tailings, the range includes a reject separator (turbo separator) with a specially designed rotor, backwash water, a closed working condition and an openable cover; a fibre separator for secondary breaking and screening; a light impurity separator, also called an apple screen; and a self-cleaning vibrating screen with an air seal chamber.

Frequently asked questions

What is the difference between an inflow and an upflow pressure screen?
An inflow pressure screen is designed mainly for fine screening and low-pulse delivery of accepted stock, which is why it is often the last screen before the paper machine. An upflow pressure screen feeds stock from the bottom, so heavy contaminants such as staples and grit leave through the bottom while light ones such as foam and plastic leave at the top. This shortens the time contaminants spend against basket and rotor and reduces abrasion. Upflow machines are chosen for coarse and fine screening of waste paper where metal and grit are present; inflow machines where final cleanliness and smooth flow matter more.
At what consistency does a mid-consistency pressure screen operate?
Normally 2.5 to 4 per cent, against roughly 0.8 to 1.5 per cent for a conventional fine screen. Higher consistency means less dilution water between pulper and screen, so smaller pumps and a smaller water circuit, which helps Indian mills short of fresh water or limited by effluent treatment. The trade-off is that rotor, seals and discharge need more attention because thick stock is less forgiving. Seal-water monitoring and a heavy-impurity discharge are therefore standard features of this type.
How do I know when a screen basket needs replacing rather than cleaning?
Clean it first if differential pressure is high but the sheet is clean; that points to blinding. Replace it if cleaning no longer restores the clean-basket differential, or if inspection shows rounded slot edges, widened slots, cracks or deformation. Rising specks with a falling differential suggest the slots have opened. Gauge several slots and compare with new-basket dimensions. If the rotor is also worn, change both together, because a new basket against a worn rotor will not perform as intended.
What is a pre-net screen and where is it installed?
A pre-net screen, also called a head box pressure screen, is the final low-consistency screen in front of the paper machine. It sits close to the fan pump and headbox so lumps, stickies and fibre bundles are stopped before the slice and forming section. Its priorities are steady flow through the slots and fast decay of pressure pulses, hence the wide accepted outlet. It does not replace coarse or fine screening upstream; it protects the sheet from what earlier stages let through.
Is a slotted basket better than a hole basket for waste paper in India?
It depends on the stage. A slotted basket, with slots between about 0.10 and 0.35 mm, removes small shives and flat contaminants that pass round holes, so it is standard for fine and final screening. A hole basket, with openings of roughly 1.5 to 3 mm, has more open area and tolerates coarse contaminants, so it belongs after the pulper. On Indian OCC lines with variable bale quality, a hole basket in the coarse stage followed by slots in the fine stage is the usual split. Slots on a dirty coarse stage blind fast, and holes in a final screen let specks into the sheet.
Can one pressure screen handle bagasse or straw pulp as well as waste paper?
Yes, but the set-up differs. Non-wood fibre carries many fines, pith and dust, which load the basket and water system more heavily than recycled fibre. Screens in bagasse and straw lines in Uttar Pradesh and Punjab typically run at lower consistency, with slot width and reject rate chosen for the fines and with pith removed earlier where possible. Inflow designs are listed for wood, straw and waste paper pulp. Review the furnish with the supplier before fixing the basket specification, because bagasse pith varies between storage and crushing season.
Does monsoon humidity or summer heat change how a pressure screen should be run in India?
Yes. In hot months higher stock temperature makes stickies softer, so they can pass fine slots and re-form lumps downstream; watch reject flow and basket cleaning intervals more closely. In monsoon, damp bales bring more grit and mud, and wet bagasse brings more pith, so coarse-stage wear and reject volume rise. Seal-water supply can also tighten in dry summers, so mid-consistency machines should have the flow alarm tested regularly. Recording differential pressure against season builds a useful local picture.
What does a rising pressure drop across a pressure screen tell me?
The drop between feed and accepts shows how loaded the basket is. A slow rise over days usually means partly blinded slots, or a reject rate set too low so contaminants thicken at the outlet. A sudden jump points to a plugged reject line or a mass of heavy contaminants at the discharge. Record the clean-basket value at start-up, set an alarm limit above it, and check reject flow, dilution and upstream cleaning before turning up dilution water to mask the reading.
Does a pressure screen replace the cleaner stage?
No. A screen separates by size and shape; a cleaner separates by density using centrifugal force. Cleaners remove sand, staples and some light contaminants, and screens remove oversize or flat particles cleaners miss. In a recycled-fibre line in India or elsewhere, both are used, with cleaning normally placed before fine screening so the basket is protected from abrasive particles. The cleaning equipment page describes how that stage is arranged.