Euskara
Zulu
Latinus
Cymraeg
தமிழ்
Slovak
Galician
AfrikaansFrom Wet-End Chemistry to Two-Sided Dewatering: A Systematic Approach to Paper Two-Sidedness
Aug 21,2026
From Wet-End Chemistry to Balanced Dewatering: Building a More Uniform Paper Sheet
Paper two-sidedness is not created at one single point on the paper machine. It develops from the interaction between stock characteristics, wet-end chemistry, sheet formation, dewatering and downstream process conditions.
For this reason, improving only the surface of the finished sheet may not solve the fundamental problem.
A more effective strategy starts with controlling the distribution of fibers, fines and fillers during wet forming, then combines mechanical forming technologies with chemical retention, drying and finishing optimization.
The ultimate objective is to achieve a more uniform sheet structure through the Z-direction, reducing differences between the two paper surfaces.
Start with Fines and Filler Retention
Wet-end chemistry plays an important role in determining how fines and fillers are retained and distributed within the sheet.
When retention is insufficient, part of the fines and filler fraction can be lost through the forming fabric during drainage. This can increase differences in composition through the thickness of the paper.
Properly selected retention aids can improve overall retention while promoting a more uniform Z-direction distribution.
The source material highlights the Dual-Component Microparticle Retention System as one approach.
Compared with a conventional single-polymer retention system, the referenced system can provide better filler retention and more uniform filler distribution. Under the conditions cited in the source material, filler retention may increase by nearly 20%.
This approach also contributes to reducing dusting and linting by improving the retention of fine components within the sheet.
Fiber Preparation Matters Before the Stock Reaches the Headbox
Chemical retention alone cannot create a uniform sheet if the fiber furnish itself is not properly prepared.
Refining should therefore be optimized according to fiber characteristics and paper quality requirements.
Appropriate refining promotes fiber fibrillation, increasing the available fiber-to-fiber bonding area.
This supports:
- Better sheet formation
- Stronger fiber bonding
- Improved paper strength
- More uniform sheet structure
Fiber furnish and refining should therefore be considered together when analyzing paper two-sidedness.
Multi-Layer Headbox Technology Provides Another Level of Structural Control
For applications requiring more deliberate control of the sheet structure, a Multi-Layer Headbox offers another technical approach.
Instead of forming the sheet from one uniform furnish, different fiber characteristics can be assigned to individual layers.
For example, a selected surface layer may contain a higher proportion of fine fibers.
By adjusting the furnish composition of each layer, the paper structure can be designed to compensate for property differences between the two surfaces.
In this case, two-sidedness is addressed through layer structure design, rather than relying entirely on downstream correction.
Balanced Dewatering Tackles the Problem During Sheet Formation
Because two-sidedness is fundamentally associated with wet-web formation, the direction of drainage is one of the most important factors to consider.
Gap Former: Two-Sided Dewatering from the Beginning
A Gap Former forms the wet web between two forming fabrics.
Water can therefore be removed toward both sides during sheet formation.
This simultaneous two-sided drainage reduces the structural differences associated with predominantly one-sided dewatering.
Rather than correcting the sheet after it has already formed, the Gap Former addresses two-sidedness much closer to its origin.
Top-Wire Former: A Practical Route for Existing Forming Sections
For an existing paper machine, installing a Top-Wire Former provides another way to introduce two-sided drainage.
The additional upper forming fabric creates an upward drainage path while the original forming section continues to provide drainage from below.
The resulting two-sided dewatering can help:
- Improve sheet formation
- Reduce structural differences
- Create a more balanced wet web
This makes Top-Wire Former technology particularly relevant when improving the forming section of an existing machine.
Dandy Roll Provides Another Route to Better Formation
Not every project requires a complete forming-section rebuild.
A Dandy Roll can provide controlled mechanical action to the developing wet web.
Its role is to improve sheet formation and promote a more uniform distribution of fibers and fillers.
This makes it another option for mills looking to improve wet-web structure using the existing forming section.
Filler Selection Should Consider More Than Dosage
Filler management also affects the uniformity of the paper sheet.
Instead of focusing only on total filler addition, mills should consider:
- Filler type
- Particle size
- Particle morphology
The source material identifies small-particle, spindle-shaped Precipitated Calcium Carbonate (PCC) as an example for promoting more uniform filler distribution.
The purpose is to improve the distribution of filler within the sheet and reduce differences between the two surfaces.
Drying Conditions Can Reinforce Existing Two-Sidedness
A well-formed wet web can still develop additional differences if the drying process is not properly controlled.
Paper machine speed should therefore be coordinated with drying capacity, while the dryer-cylinder temperature profile should be optimized to avoid excessive differences in drying rate.
A more appropriate drying profile helps prevent unnecessary stress differences from developing between the two sides of the paper.
This means that two-sidedness control should not stop when the web leaves the forming section.
Hot-Roll Calendering and Steam Treatment Provide Final Adjustment
Some differences can be further corrected during the dryer and calender stages.
The source material identifies:
Hot-Roll Calendering + Steam Box
as downstream methods for balancing stresses and adjusting surface properties.
These measures can contribute to:
- Better surface smoothness
- More balanced surface characteristics
- Reduced residual surface two-sidedness
Their role, however, is complementary.
When the fundamental problem originates during wet forming, downstream correction should support—not replace—proper stock, chemistry and forming control.
Six Technologies Working Toward the Same Objective
The principal technologies identified in the source material can be summarized as follows:
| Technology | Application Area | Role in Two-Sidedness Control |
|---|---|---|
| Gap Former | Forming Section | Uses simultaneous two-sided drainage to reduce differences caused by one-sided dewatering |
| Top-Wire Former | Forming Section | Adds upward drainage and promotes more balanced sheet formation |
| Hot-Roll Calender / Steam Box | Calender / Dryer Section | Balances stresses and adjusts surface properties |
| Dual-Component Microparticle Retention System | Wet-End Chemistry | Improves the Z-direction distribution of fines and fillers |
| Multi-Layer Headbox | Stock Delivery / Forming | Uses layered furnish design to balance sheet properties |
| Dandy Roll | Forming Section | Improves formation and promotes more uniform fiber/filler distribution |
Prevent First, Correct Later
When evaluating paper two-sidedness, one principle is especially important:
Prevent excessive two-sidedness during wet forming first, then use downstream processes for further correction.
From a long-term equipment perspective, Gap Former and Top-Wire Former technologies provide ways to move from predominantly one-sided drainage toward more balanced two-sided dewatering.
For demanding paper grades, however, equipment modification should be combined with process optimization.
A systematic improvement route can therefore be expressed as:
Fiber Furnish → Refining → Retention Chemistry → Headbox → Forming → Balanced Dewatering → Drying → Calendering
Combining mechanical and chemical measures provides a more comprehensive approach to improving sheet uniformity and meeting higher paper quality requirements.
Huatao Group – Paper Machine Forming and Dewatering Solutions
Huatao Group provides equipment, components and spare parts for pulp and paper production, with solutions covering forming, dewatering, pressing and finishing applications.
For paper mills working to improve paper two-sidedness, formation and dewatering performance, our related products include:
- Gap Formers
- Top-Wire Formers
- Dandy Rolls
- Dewatering Elements
- Suction Press Rolls
- Blind-Drilled Press Rolls
- Press Rolls
- Jumbo Press Rolls
- Calender Rolls
- Bow Rolls
If you need further assistance with paper two-sidedness, paper formation, forming-section optimization or paper machine upgrades, please contact Huatao Group

Contact Huatao Group
Website: www.huataogroup.com
Email: team3@huataogroup.com
WhatsApp / WeChat: +86 19322109200
SEO Tags
#PaperTwoSidedness #PaperMachine #PaperIndustry #PulpAndPaper #Papermaking #PaperMill #WetEndChemistry
#MicroparticleRetention #FillerRetention #PaperFormation #GapFormer #TopWireFormer #MultiLayerHeadbox
#DandyRoll #DewateringElements #BalancedDewatering #Calendering #PaperQuality #PaperMachineUpgrade #HuataoGroup #huatao
PREVIOUS:
Contact Us
E-mail:
team3@huataogroup.com
Phone/WhatsApp:
+86-13331385676
Address:
NO.298 Zhonghua North Street,Shijiazhuang city, China.