Euskara
Zulu
Latinus
Cymraeg
தமிழ்
Slovak
Galician
Afrikaans-
Website Group
We Help Customers To Meet The Great Challenges Of Our Time.
VIEW PRODUCTSCeramic vs Rare Earth Self-Cleaning Magnet for Fine Tramp Iron on a Gold Ore Conveyor: Which One Actually Pays Off?
Nov 16,2026
Ceramic vs Rare Earth Self-Cleaning Magnet for Fine Tramp Iron on a Gold Ore Conveyor: Which One Actually Pays Off?
Material Comparison: Ceramic vs Rare Earth in Detail
Field strength and gradient. Ferrite delivers Br of 3.8–4.0 kG against 11.5–13.5 kG for NdFeB. But the decisive number for fine iron is the field gradient near the pole edge. Rare earth pole geometry reaches gradients several times steeper, which multiplies capture force on small, low-mass particles. In practical terms: at a 50 mm working gap under the belt, a ceramic assembly might hold a 10 mm bolt but will lose most sub-millimeter steel; a rare earth assembly holds both.
Temperature behavior. Gold ore circuits often run hot ore, especially after drying or in hot climates. Standard N-grade NdFeB begins losing coercivity at 80 °C and can be permanently demagnetized by hot-respiking during maintenance welding. H, SH and UH grades extend this to 180–200 °C at a cost premium. Ferrite is effectively immune in the operating range of any conveyor, tolerating 250 °C and beyond. A plant that once cooked a rare earth magnet assembly will never buy standard N-grade again — this is one of the most common and most avoidable failure modes.
Corrosion and coating. Ferrite blocks barely corrode. NdFeB must be coated (typically nickel-copper-nickel, sometimes epoxy over nickel for wet circuits). Gold processing environments are often wet and occasionally acidic; a compromised coating lets rare earth blocks swell and crack from the inside. Specify coated and sealed assemblies for any wash-down or outdoor installation.
Cost structure. Ceramic magnet assemblies typically cost 50–70% of the equivalent rare earth unit, and their price is stable because iron oxide feedstock is abundant. Rare earth assembly prices move with the NdPr market — and 2026 has been an up year. When comparing quotes more than a few months apart, always confirm whether pricing still stands.
Procurement Guide
Information to provide suppliers: conveyor belt width and speed, expected burden depth and lump size, suspension height or pulley diameter, ore temperature, moisture and abrasivity, installation orientation, and — most importantly — your contamination history (photos and weights of what you have pulled out manually).
What to demand from the supplier: a written capture-rate expectation for your stated particle size range at your working gap; magnet grade certificates (Br, Hc, and temperature class for NdFeB; coating spec); self-cleaning belt specification including cleat type and belt material for your temperature; and spares availability for belts and bearings.
Buyer questions that expose weak suppliers: Can you supply a performance guarantee at my gap and speed, not a catalog value? What NdFeB temperature grade is quoted, and what happens if ore exceeds it? How is the coating tested for wet circuits? Can you support OEM replacement of an existing assembly by matching bolt pattern and face dimensions? What is the lead time, and is the quote fixed against NdPr feedstock movement or subject to re-pricing?
MOQ and shipping: single-unit orders are normal for this product class; the items that constrain lead time are usually the self-cleaning belt and coated magnet blocks. Export packing should include shock protection — hard impact can crack ferrite blocks and chip rare earth coatings before the unit is ever installed.

Failure Analysis
Problem | Possible Cause | Recommended Solution |
Fine iron passes through | Ceramic magnet specified for sub-mm targets | Upgrade to rare earth grade; reduce working gap |
Capture rate dropped over months | Iron cake build-up shielding the face; belt slipping | Clean face, restore belt tension, verify scraper |
Rare earth unit demagnetized | Ore or ambient temperature above grade limit; welding near assembly | Replace with H/SH grade; enforce hot-work exclusion zone |
Magnet face rusting | Coating breach on NdFeB in wet circuit | Epoxy-over-nickel coating; inspect annually |
Captured iron falling back onto belt | Belt speed too low to carry iron out of field; chute backplate too far | Increase cleat engagement; adjust discharge chute to within 10–15 mm |
Cleats torn off | Oversized tramp piece jamming at discharge | Add grizzly upstream; use reinforced cleat design |
Belt tracking failure | Uneven iron loading on one side | Re-center material bed; check idler alignment (Conveyor Idlers & Rollers) |
Case Study
Customer Type: mid-size gold ore processing plant, gravity-flotation circuit.
Ore Type: free-milling gold ore with quartz gangue, above-average steel contamination from old underground workings.
Operating Conditions: 1,200 t/d, 1,050 mm belt at 1.8 m/s, 120 mm suspension gap, ore temperature up to 65 °C in summer.
Problem: the plant ran a ceramic self-cleaning magnet sized for coarse protection, yet cone liners were being damaged 2–3 times per year by fine steel fragments — mostly screen wire and drill-steel filings. Manual metal detection stoppages averaged 12 per month.
Solution: replaced the ceramic assembly with a rare earth (SH-grade, 100 °C margin) self-cleaning unit at the same suspension point, and re-set the discharge chute to 12 mm clearance. Existing Belt Cleaner and conveyor components were retained.
Result: fine-iron capture mass on the discharge increased about 3×, crusher damage events fell to zero over the following nine months, and metal detector stoppages dropped by roughly 70%. The magnet premium was recovered in avoided crusher relines within one operating quarter.
Contact Us
Contact: Annie Lu
Email: annie.lu@huataogroup.com
Phone / WhatsApp: +86 180 3242 2676
Website: http://www.tufflexscreen.com
We warmly welcome customers from around the world to contact us and establish mutually beneficial partnerships.
Contact Us
E-mail:
team3@huataogroup.com
Phone/WhatsApp:
+86-13331385676
Address:
NO.298 Zhonghua North Street,Shijiazhuang city, China.
Phone/WhatsApp:
Email:
Huatao Group will make every effort to supply all industry-related products you are looking for in China. Once cooperation, lifelong partner.
HUATAO GROUP
Leave Message
LINKS: