Euskara
Zulu
Latinus
Cymraeg
தமிழ்
Slovak
Galician
Afrikaans-
Website Group
We Help Customers To Meet The Great Challenges Of Our Time.
VIEW PRODUCTSWhat Specifications Should I Check Before Purchasing a Sectional Screw Flight Forming Machine?
Nov 18,2026
For screw conveyor manufacturers, purchasing a screw flight forming machine is not simply about choosing equipment with a large forming capacity. The machine must match the actual flight dimensions, plate thickness and material used in production.
A common concern among buyers is whether they must prepare a complete engineering drawing before contacting a manufacturer.
For the initial selection of a HUATAO single-piece hydraulic flights screw forming machine, a complete drawing is not necessary. We can begin with five basic specifications: inner diameter, outer diameter, thickness, material and pitch.
These details allow our team to evaluate the appropriate model and discuss a suitable machine configuration.
1. Inner Diameter: Make Sure the Flight Fits the Shaft
The inner diameter (ID) is the opening at the center of the finished spiral blade. It determines the fit between the flight and the shaft or tube used in the screw conveyor.
A buyer should provide the required finished ID rather than only the shaft diameter.
The available machine models have different minimum ID ranges. For example, the HT240 brochure specification lists an ID greater than 63 mm, while the HT280 lists an ID greater than 89 mm. The HT330 lists an ID greater than 168 mm.
This is why the required ID should be checked during model selection.
2. Outer Diameter: Identify Your Largest Flight
The outer diameter (OD) determines the overall size of the finished screw flight.
HUATAO's brochure includes single-piece hydraulic forming models ranging from smaller equipment to the HT330, whose listed OD range is below 2400 mm.
However, the largest diameter is not the only factor. A buyer should provide the actual OD together with the ID, thickness, material and pitch.
These five dimensions and material details help determine whether a standard model is suitable or whether a customized configuration should be considered.
For machine information, visit the Spiral Blade Forming Machine page.
3. Thickness: Select the Correct Hydraulic Forming Capacity
The thickness of the steel plate affects the forming requirements and the machine configuration.
The HUATAO brochure lists different thickness ranges for its single-piece hydraulic models. For example:
HT120: 2–14 mm
HT160: 2–25 mm
HT180: 2–30 mm
HT240: 2–35 mm
HT280: 2–40 mm
HT330: 2–50 mm
These specifications are model-specific. The maximum thickness should not be treated as an independent guarantee for every diameter, pitch and material combination.
When requesting a machine recommendation, provide the actual plate thickness you plan to process.
4. Material: Choose the Machine According to the Steel Grade
The material is essential to the selection process because different grades have different forming characteristics.
The machine brochure identifies the following materials:
Carbon steel
304 stainless steel
201 stainless steel
HARDOX steel
If your workshop processes different materials for different customer orders, tell us the complete material range.
This helps us evaluate the required machine and tooling configuration rather than recommending equipment based only on one standard material.
5. Pitch: Check the Required Spiral Spacing
Pitch is the axial distance between corresponding points on adjacent turns of the screw flight.
It affects the final spiral geometry and should be considered together with diameter and thickness.
For example, the brochure lists an HT240 pitch range of 180–1000 mm, while the HT280 and HT330 list 240–900 mm.
The correct model depends on the full combination of the five specifications, not one maximum value in isolation.
6. Why Five Specifications Are Enough for Initial Selection
A complete drawing is not required at the first stage of machine selection.
HUATAO can start the evaluation with:
Inner diameter (ID)
Outer diameter (OD)
Thickness
Material
Pitch
Based on these details, we can recommend a suitable model or discuss customization according to your product requirements.
A drawing or sample may still be helpful later if the flight includes special profiles or non-standard details. However, it is not necessary just to begin the selection process.
7. Understand the Difference Between Machine Types
HUATAO supplies different types of spiral blade forming equipment. Buyers should identify the production method they need before purchasing.
The machine discussed in this article is a single-piece hydraulic screw flight forming machine. It presses individual spiral blade sections.
A continuous cold-rolling machine follows a different process and is intended for continuous flight production. You can compare it with the Continuous Screw Flight Cold Rolling Machine.
A winding machine uses another forming route. See the Winding Spiral Blade Forming Machine for this separate equipment category.
Selecting the correct machine type helps avoid comparing equipment that serves different production needs.
8. Warranty, Service Life and Maintenance
A machine purchase should also be evaluated according to long-term operating costs.
HUATAO provides a one-year warranty for the machine. Under suitable operating and maintenance conditions, the expected service life can reach approximately 7–8 years.
The machine has very few wearing parts. The replacement parts are inexpensive and easy to change, making routine maintenance more straightforward.
Actual service life depends on operating conditions, maintenance and usage intensity. Buyers should confirm the warranty scope and maintenance requirements in the quotation and technical documents.
Frequently Asked Questions
Do I need to send a drawing to select a HUATAO machine?
No. For initial model selection, provide ID, OD, thickness, material and pitch.
Which models are available for larger screw flights?
The brochure includes HT240, HT280 and HT330 models, with listed maximum OD ranges below 1200 mm, 1600 mm and 2400 mm respectively. The complete dimensional combination must still be confirmed.
Which materials can be processed?
The brochure lists carbon steel, 304 stainless steel, 201 stainless steel and HARDOX steel.
Can HUATAO customize a machine?
Machine selection and configuration can be discussed according to the required flight dimensions and material.
What warranty is included?
The machine is supplied with a one-year warranty.
What is the expected service life?
It can reach approximately 7–8 years under suitable operating and maintenance conditions.
Request a Machine Recommendation from HUATAO
If you manufacture screw conveyor flights, auger blades or industrial spiral components, start with five details.
Send us your ID, OD, thickness, material and pitch. HUATAO will evaluate the suitable single-piece hydraulic screw flight forming machine according to your requirements.
Contact
Lucy Chai
Email:Lucy.chai@huataogroup.com
WhatsApp: +86 15373883537
www.refinerdisc.com
Contact Us
E-mail:
team3@huataogroup.com
Phone/WhatsApp:
+86-13331385676
Address:
NO.298 Zhonghua North Street,Shijiazhuang city, China.
Phone/WhatsApp:
Email:
Huatao Group will make every effort to supply all industry-related products you are looking for in China. Once cooperation, lifelong partner.
HUATAO GROUP
Leave Message
LINKS: