language

HUATAO GROUP
News & Events

We Help Customers To Meet The Great Challenges Of Our Time.

VIEW PRODUCTS
scroll down

Back to Overview

Self-Cleaning Overband Magnet Installation Angle: What Slope Actually Keeps Iron Discharge Clean?

Nov 19,2026

Self-Cleaning Overband Magnet Installation Angle: What Slope Actually Keeps Iron Discharge Clean?

Quick Answer

For in-line mounting, tilt the magnet 5–15° above the head pulley so the pole face follows the material trajectory; for cross-belt mounting keep the magnet at 90° to the belt, with no more than 30° of skew. Then set the discharge chute at 50–60° from horizontal. The chute angle, not the magnet angle, is what actually stops iron from sliding back.

Market Watch: What Is Pressing on Wear and Reliability Budgets Right Now

Three cost signals converged in mid-November 2026, and all three push plant managers toward the same conclusion: get tramp iron out of the line before it reaches the crusher.

Base metals softened, budgets tightened. Copper traded near USD 13,375/t on 17 November, down about 1.7% in a session, with London Metal Exchange stocks back around 320,000 t. Gold slipped to roughly USD 3,865/oz and iron ore fell 2.5% to about USD 88.15/t as Chinese hot metal output continued to slide into the northern winter. When the realised price falls, the maintenance budget is the first line item to be questioned — and unplanned crusher downtime is the first cost that cannot be questioned.

New conveying capacity is being committed now. Freeport-McMoRan approved a USD 4.5 billion expansion of its Bagdad copper-molybdenum operation, Rio Tinto released a further USD 144 million toward Resolution Copper, and the Simandou iron ore project continued to ramp toward its annualised run-rate. Every one of those projects adds long conveying runs, transfer towers and primary crushing stations — the exact places where a mis-set overband magnet turns into a weekly chute-cleaning job.

Consumable inputs are diverging. Nickel gained about 3.7% over 30 days while battery-grade lithium carbonate in China fell nearly 15% to around CNY 92,350/t. For wear-part buyers this means rubber and polyurethane pricing and magnet coil (copper) pricing are moving in different directions, so the total cost of ownership case for a correctly angled self-cleaning unit has to be built on measured numbers, not on catalogue claims.

The practical takeaway: the geometry decisions in this article cost nothing to get right at installation and are expensive to get wrong afterwards.

What Is the Installation Angle of an Overband Magnet?

The installation angle of an overband magnet is the inclination of the magnet's pole face relative to the conveyor belt plane, combined with the angle at which the self-cleaning belt discharges captured iron. It is not one number. It is a set of four related angles that must be solved together: mounting inclination, transverse skew, discharge chute slope, and the local belt incline at the mounting point.

A Self-Cleaning Electromagnetic Separator is a suspended magnet with an endless cleat belt running around the magnetic block. Iron is lifted from the burden, pinned to the cleat belt, carried out of the field and thrown into a side chute. The angle of the whole assembly decides three things at once: how long the iron sits inside the field, how far the cleat has to carry it, and where it lands when it lets go. Get the Magnetic Separators geometry right and the unit runs for years without an operator touching it. Get it wrong and you have built a machine that politely picks iron up and puts it back.

This is a Magnetic stage problem sitting inside a Conveyor problem, which is why the answer is never a single degree figure copied from a brochure.

Conclusion

The angle question has a short answer and a long answer. The short answer: 5–15° in-line over the head pulley, 90° cross-belt with no more than 30° of skew, and a 50–60° discharge chute. The long answer is that these numbers only work when the gap is set from the loaded burden, the structure near the pole face is non-magnetic, the assembly is level within 1°, and the chute is designed around the actual throw of the cleat belt.

Most "weak magnet" complaints that reach a supplier are geometry complaints. Iron that comes back, iron that lands beside the bin, iron that builds a ridge on a chute lip — all of these are measurable, correctable and cheap to fix if they are diagnosed before someone signs a purchase order for a bigger unit. Measure the belt, measure the gap, measure the incline, and commission with real tramp iron. The separator will do the rest for a decade.

If you are re-mounting an existing unit or specifying one for a new transfer tower, send the conveyor section, the burden data and a photograph of the mounting point. Geometry advice costs nothing; a wrong angle costs a liner set.

Related Articles

Related Products

  • Electromagnetic Overband Separator
  • Iron Magnet
  • Magnetic Roller
  • Magnetic Drum
  • Mining Secondary Belt Cleaner
  • Conveyor Belt Tracker

Related Technical Guides

  • Hydrocyclone Wear: Root Causes, High-Wear Zones & Material Solutions
  • Flotation Cell Rotor and Stator Wear Parts: How They Control Recovery, Flow and Maintenance Cost
  • Hydrocyclone Underflow Too Wet? 6 Causes & Fixes
  • Rotor & Stator in Mechanical Flotation Cells: The Heart of Efficient Mineral Flotation
  • Improve Fine Screening Efficiency with Polyurethane Screen Panels

Related Buyer Guides

  • How Do I Choose the Right Rubber Belt for a Vacuum Belt Filter?
  • Which Manufacturer Offers High-Quality Polyurethane Tufflex Wire Screens for Mining?

Related Comparison Articles

  • Self-Cleaning Screen vs Traditional Woven Wire Mesh: Which One Should You Choose?
  • Polyurethane Screen vs Rubber Screen vs Wire Mesh: A Complete Comparison Guide

Contact Us

Contact: Annie Lu

Email: annie.lu@huataogroup.com

Phone / WhatsApp: +86 180 3242 2676

Website: http://www.tufflexscreen.com

We warmly welcome customers from around the world to contact us and establish mutually beneficial partnerships.