language

HUATAO GROUP
News & Events

We Help Customers To Meet The Great Challenges Of Our Time.

VIEW PRODUCTS
scroll down

Back to Overview

What Is a Spiral Chute and How Does It Work

Nov 16,2026

What Is a Spiral Chute and How Does It Work

A spiral chute is the quietest machine in a mineral processing plant: no motor, no reagents, no moving parts — just a helical trough and the physics of a flowing film. This guide walks through what it is, how the separation actually happens, where it fits in a flowsheet, and the operating disciplines that decide whether it recovers values or reproduces shortcuts in the tailings.

1. Quick Answer

A spiral chute is a stationary gravity separation device: an inclined helical trough, five to seven turns tall, down which dilute slurry flows as a thin film. Heavy, round grains in the 0.1–2 mm band sink through the film, reach the slow layer at the trough wall, and migrate to the inside of the helix; light grains ride the fast outer stream. Splitters at the discharge cut concentrate, middlings and tailings. The machine uses no power and no reagents, and its performance depends almost entirely on feed preparation, flow stability and splitter discipline.

2. Key Takeaways

  • Two overlapping flows do the sorting: a fast downstream film plus slow secondary circulation across the trough.
  • The first two or three turns separate; the rest of the helix merely transports.
  • Working window: 0.1–2 mm feed, deslimed below ~50 microns, 20–40% solids, 1–3 t/h per start, constant.
  • A concentration criterion above about 1.5 is the entry ticket for gravity duty.
  • The three silent killers are liner wear at the top turns, splitter drift and feed surge.
  • Middlings are unfinished business — return them to feed and finish on tables or concentrators.

3. Summary Table

Parameter

Typical Range

Why It Matters

Feed size

0.1–2 mm (best 0.15–1 mm)

Values outside the band never stratify properly

Desliming cut

Minus ~50 µm removed

Slimes ride the film and dirty middlings

Feed density

20–40% solids

Thin films starve; thick films short-circuit

Capacity per start

1–3 t/h

Stability beats peak capacity

Products

Concentrate, middlings, tailings

Splitters are the grade-recovery dial

Power at machine

Zero

Operating cost is one pump and one water line

 

4. Definition: What Counts as a Spiral Chute

A spiral chute is a semicircular trough wound into a vertical helix of five to seven turns, two to four metres tall, standing on a light steel frame. Modern columns are built from glass-reinforced plastic, often polyurethane-faced in abrasive duty, and most banks use double-start or triple-start units so that two or three independent streams share one column. "Spiral chute" and "spiral concentrator" are two names for the same machine; what separates one quotation from another is pitch, trough diameter, start count, liner material and the test work behind the recommendation. The device belongs to the gravity separation equipment family beside shaking tables and centrifugal concentrators — the high-tonnage, low-cost end of the range, as shown on the spiral chutes product page.

5. Working Principle: Two Flows in One Trough

The separation mechanism has two parts running at once, and every operating decision follows from them.

The downstream film. A feed box spreads slurry into a thin, even film across the trough width. Gravity accelerates it down the helix, and curvature makes the outside of the bend run faster than the inside — the same differential that sweeps a river around the outside of its bend. Light, flaky and coarse particles ride this fast outer stream and never settle.

The secondary circulation. The same curvature rolls the film across the trough: the surface layer flows outward while the bottom layer drifts inward. This is the engine of the separation. Heavy, spherical particles drop through the film within the first turns, enter the slow near-wall layer, and are carried inward toward the helix's inside edge. Wash water dosed along the inner radius keeps the collected heavy strand fluid; without it the strand packs and begins shedding values.

The split. By the bottom turn, three zones span the trough width — a slow heavy strand inside, a fast light stream outside, a middling band between them. Adjustable splitters convert the zones into product launders. The splitters are not trim; they are the actual grade-recovery dial, and the correct position moves with feed grade.

Two consequences matter. Particle shape competes with density: a flat light flake hugs the wall and impersonates a heavy mineral, which is why scrubbing precedes spirals in clay-bound circuits. And because the top turns do the sorting, liner wear there is the first place recovery leaks.

Reading the film. Two minutes at a running spiral tell an experienced operator more than a shift of sampling. An even, glassy film with a clean dark strand inside means the feed is right. A dry patch means the distributor is starving that column. A fuzzy, clouded film means slimes arrived that desliming should have caught. A strand that breaks and reforms means the feed rate is hunting. All four symptoms are upstream problems wearing a spiral's clothes, and all four are cheaper to fix at the feed box than at the concentrate launder.

One column, one helix: feed at the top, three products at the bottom, nothing between but geometry.

6. Benefits: What the Machine Is Worth

  • Zero power at the machine. Ten years of operating cost is one feed pump and one water line.
  • No reagents. Nothing to dose, nothing to neutralise downstream.
  • Capacity per square metre. Double-start columns put two streams in one footprint; a row of twenty columns can rough 100 t/h.
  • Forgiving to run. One operator walks the row per shift; a gurgling start is surging, a silent start is starving.
  • Fast installation. A flat pad, a feed head, one launder.
  • Graceful degradation. Liner wear trends slowly, and monthly inspection manages it — the failure mode is a trend, not an event.
  • Scalable in steps of one start. Capacity grows by adding columns, not by redesigning the flowsheet; a bank that undershoots demand is extended, not replaced.

7. Applications: Which Minerals Suit Spirals

  • Tin and tungsten: cassiterite and wolframite against quartz, in primary and alluvial ores. The duty is commercially live: in November 2026, Peru's Minsur filed for environmental approval to retreat roughly 651,000 tonnes of B3 tailings at its San Rafael tin mine for about US$22 million, returning cassiterite preconcentrate to the existing plant — sand-size tin recovery is exactly this machine's territory.
  • Mineral sands: ilmenite, rutile, zircon and monazite roughed from quartz in wet plants.
  • Chromite: metallurgical and beach deposits, always after scrubbing and desliming.
  • Iron ore: gravity roughing of fine hematite and goethite where flotation is not justified by value.
  • Alluvial gold: roughing ahead of tables, with washing plant ahead of the whole chain from the gold process equipment range.
  • Garnet, monazite and slag recovery: anywhere a density ratio survives in a sand-size feed.

8. Material Comparison

Material

Where Used

Strengths

Watch-outs

GRP (glass-reinforced plastic)

Full trough

Smooth, light, low cost

Gelcoat wears first at top turns

Polyurethane facing

Full trough / hot spots

Longest wear life, stable surface

Higher unit cost

Cast basalt / ceramic

First two turns only

Extreme abrasion resistance

Retrofit complexity

Steel frame

Structure

Rigid, cheap

Corrodes in wet coastal climates

 

Polyurethane facing pays for itself in abrasive or high-tonnage duty; plain GRP suits small, gentle circuits. Replacement strategy matters more than material choice: the top turns of a whole row should be replaced together, because mixing old and new surfaces in one bank splits its performance. Matched trough sections, feed boxes and splitters are supplied in the gravity separation spares range.

9. Application Comparison

Device

Capacity

Power

Natural Role

Spiral chute

1–3 t/h per start

None

Roughing, scavenging

Shaking table

0.5–2 t/h

Yes

Final cleaning

Centrifugal concentrator

2–10 t/h

Yes

Fine gold, upgrading

Jig

10+ t/h

Yes

Coarse pre-concentration

 

Flowsheets that let each device do its natural job get the most from all of them: spirals rough, shaking tables finish, and centrifugal concentrators catch what film flow misses.

10. Industry Application Matrix

Industry

Duty

Spiral Passes

Tin mining

Cassiterite roughing, tailings retreatment

Rougher + scavenger + cleaner

Mineral sands

Heavy mineral preconcentration

Long rougher rows

Chromite

Beach and metallurgical ore

Roughing after scrubbing

Gold (alluvial)

Feed preparation and roughing

Roughing ahead of tables

Iron ore

Fine hematite roughing

Rougher + cleaner

Recycling and slag

Metal and garnet recovery

Scavenging rows

 

11. Selection Guide: Work Back From the Feed

  1. Confirm the concentration criterion — (SG heavy − 1)/(SG light − 1) — is comfortably above 1.5.
  2. Confirm the values sit inside 0.1–2 mm; if not, the project is a classification problem first.
  3. Plan desliming: minus-50-micron material goes to hydrocyclones, never to the helix. Grinding circuits take their size cut from a spiral classifier.
  4. Break down clay-bound feed with a screw washer or scrubber before classification.
  5. Size the start count: feed tonnage ÷ t/h per start; add cleaner and scavenger passes from the rougher mass balance; group into banks with a common distribution box.

A 100 t/h roughing duty at 2.5 t/h per start means 40 starts — twenty double-start columns — plus cleaning capacity sized from the rougher concentrate mass.

A small-site installation: two starts, one frame, gravity feed from a header tank.

12. Procurement Guide: What to Send and Ask

Send: head assay and target mineral with its specific gravity; feed size distribution after planned desliming; slurry density and hourly feed rate; available head and a plant layout sketch; water quality and climate constraints.

Ask: which similar feed the supplier has actually run and at what recovery; how the recommended split position is verified during commissioning; what liner wear allowance applies at the first two turns for this duty; what spares set ships with the bank; whether trough sections can be replaced column by column without re-levelling the row. A quotation built without test work is a guess with a price — the machine is cheap, the downtime from a wrong recommendation is not.

13. Failure Analysis: The Three Quiet Killers

Liner wear at the top turns. A roughened surface sheds the heavy strand early and bleeds recovery for months before anyone notices. Inspect monthly with a torch and a feeler; replace trough sections as a set.

Splitter drift. Operators rotate, feed grade steps, splitters stay where they were. Grade loss at constant recovery is a splitting decision, not a machine fault. Record feed grade and splitter position together, and re-cut when grade steps change.

Feed surge. A spiral has no reserve. Pump cycling, an uneven distribution box or a surging tank turns a good separation into noise. Fix the feed, not the spirals — and listen: starts that sound different from their neighbours are describing distribution problems, not their own health.

Behind all three sits slimes. Minus-50-micron material stays suspended in the film, never reaches the wall layer, and exits as dirty middlings that contaminate everything downstream. When recovery disappoints, audit desliming first.

14. Maintenance Guide

  • Daily: walk the row; listen to every start; check splitter positions and wash water; note strand colour and width at the first turns.
  • Weekly: inspect feed boxes and distribution launders for scale and grit; verify equal flow to every start.
  • Monthly: measure liner wear at the top two turns; assay shift-average tailings; reconcile recovery against feed grade.
  • Annually: replace trough sections row-wide as one job; check frame level and anchors; refresh corrosion protection.

Everything is reachable, nothing is buried, and no item needs a shutdown longer than a coffee break. That is the maintenance argument for a machine with no moving parts: the few parts that do wear — liners, splitters, feed boxes — are all bolted items at the ends of the column, and a two-person crew can service an entire bank in a planned half-shift.

15. Case Study: Sand-Size Tin From Old Tailings

Minsur's November 2026 filing for San Rafael, its tin operation in Puno, Peru, describes retreating about 651,000 tonnes of B3 tailings plus roughly 540,000 tonnes of usable material from the Larancota waste dump, for about US$22 million, with preconcentrate returning to the existing plant. The arithmetic works because the duty fits the machine: cassiterite is heavy, the tailings are already sand-sized, history has done the desliming, and gravity roughing at near-zero operating cost turns historical waste into feed. The same template applies wherever old tailings still hold values between 0.1 and 2 mm with a workable density ratio — audit the tailings inventory before buying new ore, because the cheapest tonnage a plant will ever process is the tonnage it already owns.

16. FAQ

What is the difference between a spiral chute and a spiral concentrator?

Vendors use both names for the same helical trough device. Compare pitch, diameter, start count, liner material and test work, not the label on the drawing.

How fine can a spiral chute recover values?

Reliably down to roughly 50 microns. Below that, efficiency falls steadily; below 20 microns the device is effectively a washing machine. Fine fractions belong on tables, centrifugal concentrators or flotation.

How many spirals does a plant need?

Feed tonnage ÷ t/h per start, times the number of passes the flowsheet requires, plus cleaning capacity sized from the rougher concentrate mass. Example: a 100 t/h plant at 2.5 t/h per start needs 40 roughing starts — twenty double-start columns — plus a cleaner bank at roughly a fifth to a quarter of roughing capacity, run at lower density and tighter splits. Specify one spare column per bank where downtime matters; trough replacement then becomes a planned event rather than an emergency.

Do spiral chutes need power?

None at the machine. The plant pays for feed pumping, wash water and elevation head.

Why does concentrate grade fall when feed grade falls?

The splitters are fixed while the feed is not. A strand set for yesterday's grade now cuts water into the concentrate. Re-cut on grade steps and record positions against feed assays. Plants that keep a splitter log — feed assay, position, resulting grade — turn this from a mystery into a lookup table, and new operators inherit the settings instead of reinventing them. The notebook costs nothing and outperforms any instrument on a device this simple.

Can a spiral handle clay-bound feed?

Not directly. Scrub first, deslime second, spiral third — clay rides the film and contaminates every product the machine makes.

17. Conclusion

A spiral chute converts a density difference into three product streams using gravity, film flow and water. Nothing moves, nothing runs except one pump, and nothing about the result is automatic: prepare the feed, hold the flow steady, cut the products deliberately, and a row of spirals outworks far more expensive separation equipment. Skip any of the three and the machine faithfully reproduces your shortcuts in the tailings launder. On a device with no moving parts, the moving part is the decision — so write it down, and start from the spiral chute | spiral concentrator specification page when you compare quotations.

Related Articles

  • Rotor & Stator in Mechanical Flotation Cells: The Heart of Efficient Mineral Flotation
  • How Do I Choose the Right Rubber Belt for a Vacuum Belt Filter?
  • Improve Fine Screening Efficiency with Polyurethane Screen Panels

Contact

Contact: Annie Lu

WhatsApp / WeChat: +86 18032422676

Website: www.tufflexscreen.com

HTL Solutions (Tufflex brand) — gravity separation equipment and matched wear spares for mineral processing plants. Send feed size distribution, slurry density and target mineral for a start-count recommendation before quoting.

PREVIOUS: