Euskara
Zulu
Latinus
Cymraeg
தமிழ்
Slovak
Galician
AfrikaansHow Can Corrugated Box Manufacturers Reduce MOQ Without Losing Profit?
Oct 02,2026
Lowering Minimum Order Quantities (MOQs) sounds appealing: it enables corrugated box manufacturers to secure custom orders, prototyping projects, replenishment orders, e-commerce business, and other small-batch orders that high-volume competitors might be reluctant to handle.
The challenge is that simply accepting small-batch orders can severely squeeze profit margins. Costs associated with setup, tooling, labor, equipment changeovers, and scrap generated during preparation remain, yet they must be amortized across a smaller number of finished boxes. Therefore, the right approach is not to ask, "How low can we set our MOQ?" but rather, "How can we make small-batch orders economically profitable?"
Two strategies deserve particular attention: increasing the value generated by each box and reducing the amount of corrugated board required to produce each finished box.
Why Does Lower MOQ Usually Mean Higher Cost per Box?
An order for 100 boxes is not simply equivalent to an order for 10,000 boxes divided by 100.
Both types of orders typically require job preparation, machine setup, test runs, quality inspections, tooling preparation, and production scheduling. For long-run orders, these costs are distributed across thousands of boxes, whereas for short-run orders, each box must bear a significantly larger share of the costs.
A simple framework is:
Total Order Cost = Material + Setup + Tooling + Labor + Waste + Machine Time + Other Costs
Unit Cost = Total Order Cost ÷ Saleable Boxes
What Changes as Order Quantity Falls?
| Cost factor | Large repeat order | Small custom order | Profit response |
|---|---|---|---|
| Setup | Spread across many boxes | High cost per box | Shorten setup |
| Tooling | Easier to amortize | Can dominate unit cost | Use die-less production where suitable |
| Board waste | Spread over a long run | Strong impact on margin | Improve material utilization |
| Changeovers | Relatively infrequent | Frequent | Simplify job changes |
| Box value | Often commodity-driven | Greater customization potential | Sell more value per box |
This leads to two different ways of protecting profit margins.
Strategy 1: Increase the Value of Each Box
Setting a lower Minimum Order Quantity (MOQ) does not mean that similar cardboard box products must be sold at the same unit price.
Customers placing small-batch orders often have unique requirements—such as custom dimensions, prototyping, urgent restocking, a wide variety of SKUs, bespoke packaging, or order quantities precisely matched to actual needs. While these demands increase production complexity, they also create added value for the customer.
Therefore, when determining prices, manufacturers should look beyond the volume (i.e., surface area) of corrugated board used and also factor in the associated services and production complexity.
Factors such as custom dimensions, printing specifications, order urgency, the number of SKUs, specialized box designs, delivery frequency, and additional manual handling all impact actual production costs.
For an order of 20,000 identical cartons, the unit price might be the decisive factor in the purchasing decision; whereas for a customer urgently needing 80 custom-sized cartons next week, flexibility and supply capability may represent the true value of the purchase.
This shifts the business objective:
Do not lower your minimum order quantity (MOQ) just to accept small-batch orders, thereby falling into a low-margin, commodity-style price war. Instead, you should develop a small-batch supply model where "flexibility" itself becomes the source of value.
Corrugated board manufacturers can further expand upon this concept. Beyond simply selling traditional cut-to-size sheets, suitably equipped plants can explore producing "fanfold" corrugated board as a high-value-added product for customers utilizing automated or on-demand box-making workflows. According to HUATAO, combining fanfold board with automated box-making technology offers an effective way for corrugated box plants to meet the demand for small-batch and customized packaging.

Strategy 2: Reduce Waste per Saleable Box
Increasing sales value focuses on the revenue side, whereas the second strategy directly targets costs.
Corrugated board is the primary raw material used to manufacture each carton. If a factory consumes significantly more board than is required for the finished carton blanks, the excess material becomes trim waste, setup waste, or unusable scrap.
This is particularly critical for small-batch orders, as there are fewer finished cartons over which to spread these losses.
Production teams should examine the following issues:
- Is the starting sheet unnecessarily large for the required blank?
- Can blank orientation improve sheet utilization?
- How much board is consumed during make-ready?
- Is excessive edge trim being generated?
- Can compatible jobs be grouped to improve material utilization?
- Would a different material format suit highly variable short-run jobs?
A more appropriate way to measure this metric is by the "amount of cardboard consumed per sellable carton" rather than simply the "amount of cardboard processed per hour."
"Right-sized packaging" exemplifies this principle. Commercial on-demand packaging systems create cartons based on the required dimensions—rather than relying solely on pre-sized stock boxes—and reducing material usage is one of the intended benefits.
Fanfold Board Can Change the Material Equation
For certain applications involving a wide variety of products and small batch sizes, fanfold corrugated board offers an alternative production method.
"Fanfold" refers to continuous corrugated board material folded into a zigzag stack. When paired with suitable box-making equipment, this material enables a flexible production process in which the board can be cut, creased, and slotted to meet specific box dimensions.
Its potential advantages extend beyond mere machine operating speeds.
Instead of preparing specific board sizes and performing routine production setups for every small-batch order, a facility can use just a few widths of fanfold board to produce boxes in a wide range of sizes. For instance, an industrial case study documented by Packsize shows how a factory replaced a large inventory of pre-made boxes with just seven widths of fanfold board, using these few specifications to produce appropriately sized boxes for various needs. This is merely one example; results may vary for other box-manufacturing facilities.

Reduce the Fixed Cost of Every Small Order
Improving material utilization alone cannot solve the issue of Minimum Order Quantity (MOQ).
If an order for 50 cases requires time-consuming equipment setup, specialized tooling, and the consumption of a large number of test boards, the economic efficiency per unit may remain suboptimal—even if the final blank layout is highly efficient.
For this reason, changeover efficiency has become another critical Key Performance Indicator (KPI) for small-batch production.
Rather than focusing solely on "cases produced per hour," consider the following metrics as well:
Order setup time + make-ready waste + productive run time + changeover time
For high-volume, repeat orders, traditional production lines remain highly cost-effective. However, if equipment spends a significant amount of time on setup for short-run orders rather than actually producing sellable cartons, the "maximum running speed" metric becomes less relevant.
For cartons with simple designs, flexible digital box-making equipment helps reduce reliance on specialized dies, thereby eliminating or lowering fixed costs associated with certain short-run orders. This does not, however, mean that traditional die-cutting processes should be abandoned; different production methods suit different economic requirements.
Don't Force Every Order Through the Same Production Route
This is one of the most practical improvement measures a corrugated box plant can adopt.
High-volume, repetitive orders are best suited for traditional, high-output equipment; small-batch orders with compatible specifications can be consolidated to minimize changeovers; highly customized small-batch orders may be ideal for flexible or die-less production processes; and for orders with constantly changing dimensions, using fanfold board might be the optimal choice.
The specific quantitative thresholds for these categories should be determined based on your plant's own cost data.
A plant capable of rapid changeovers on traditional equipment will reach very different conclusions than one facing long make-ready times. Similarly, the requirements of a plant that primarily handles repetitive orders differ vastly from those of a plant processing a large volume of custom-sized orders daily.
Therefore, a reasonable Minimum Order Quantity (MOQ) depends on the specific production workflow.
Should You Lower MOQ for Every Customer?
Not all orders are subject to the same Minimum Order Quantity (MOQ).
Before lowering the MOQ, a cost analysis should be conducted to ensure that the order's revenue sufficiently covers materials, production setup, tooling, labor, waste, machine hours, and the company's required profit margin.
It is also worth considering whether alternative production methods could alter this cost structure.
This approach avoids treating the MOQ merely as an arbitrary sales rule. Instead, factories can establish distinct business models tailored to standard production, small-batch customization, prototyping, urgent orders, and other specific requirements.
A More Profitable Formula for Small Orders
Sustainably reducing the minimum order quantity ultimately aims to alter both sides of the profit equation:
Higher value per box + Lower material waste + Lower setup burden + Appropriate production route + Complexity-based pricing
The first two elements are particularly powerful because they address the issue from vastly different directions:
Increasing the value generated by the corrugated board being sold.
Simultaneously reducing the amount of board consumed to create that unit of value.
For plants with significant demand for "high-mix, low-volume" orders, fanfold corrugated board and automated box-making equipment can effectively support this strategy. When evaluating these solutions, they should be viewed as specialized production options rather than mere replacements for traditional corrugated board processing methods. The final decision depends on order volumes, box dimensions, flute and board specifications, the daily production mix, the condition of existing equipment, and capacity requirements.

Evaluate a Fanfold + Automatic Box-Making Workflow
If small-batch, customized orders represent an increasingly significant share of your business, we recommend evaluating them separately from traditional long-run production operations.
HUATAO provides solutions for corrugated board and box production. If you are interested in fanfold board and automated box-making systems, please provide the following information: typical minimum and maximum box dimensions, minimum and average order quantities, box styles, flute types, board grades, daily order mix, required production capacity, existing production processes, and available installation space. Based on these parameters, we can assess whether a dedicated, flexible production line aligns with your specific order profile.
FAQ
Why is the per-box cost higher for small-batch corrugated box orders?
Costs associated with setup, tooling, labor, line changeovers, and waste generated during preparation must be amortized across a smaller number of finished boxes. Consequently, as order volume decreases, the proportion of these fixed or semi-fixed costs within the unit cost rises.
How can corrugated box manufacturers lower their Minimum Order Quantity (MOQ)?
The first step is to accurately calculate the actual cost of each small-batch order. Strategies to achieve this include improving board utilization, minimizing waste during setup and changeovers, reducing unnecessary tooling usage where appropriate, adopting processes suited for small-batch production, and implementing reasonable pricing strategies for customized requirements and complex designs.
Does fanfold corrugated board help lower the Minimum Order Quantity?
This material is highly beneficial for applications involving high product variety and small batch sizes; when paired with suitable box-making equipment, fanfold board allows for the flexible production of boxes in a wide range of sizes. Its economic viability, however, depends on the factory's specific order mix, material requirements, existing equipment, and total production volume.
Should box manufacturers purchase new equipment solely to handle small-batch orders?
Not necessarily. Manufacturers should first optimize the scheduling, material utilization, setup processes, and pricing strategies of their existing equipment. Investing in flexible box-making systems or fanfold-based production solutions is only worth considering when the volume and frequency of small-batch business are sufficient to justify a dedicated production line.
Contact Us
E-mail:
team3@huataogroup.com
Phone/WhatsApp:
+86-13331385676
Address:
NO.298 Zhonghua North Street,Shijiazhuang city, China.