language

HUATAO GROUP
News & Events

We Help Customers To Meet The Great Challenges Of Our Time.

VIEW PRODUCTS
scroll down

Back to Overview

Paper machine dewatering elements: a section guide

Nov 18,2026

Paper machine dewatering elements: a section guide

A sheet leaves the headbox as roughly 99% water. Before it reaches the dryer cylinders it has to lose most of that, because every kilogram of water that survives the press section must be evaporated with steam. On a paper machine in India, where boilers are often fired on husk, bagasse or coal and the steam supply is already stretched, the first few metres of the machine matter more than they look. The forming board, hydrofoils, vacuum boxes, felt suction box and suction couch roll are the dewatering elements for the paper industry, and they work out of sight, under the fabric.

This guide follows the sheet down the machine in the order the water leaves it. It covers what each element does physically, which wearing-surface materials are used, how the pieces interact, and what an engineer in an Indian mill should look at when a machine runs out of drainage before it runs out of drive or dryer capacity. Fabric weave and felt compaction, which Indian mills also have to manage, are covered in their own guides; here the focus is the fixed and rotating hardware underneath them.

Where the water goes: paper machine dewatering elements in sequence

Think of dewatering as a relay with several runners, each suited to a range of sheet solids. Early on the stock is so dilute that water drains by gravity and by the pulse a moving fabric generates over a foil. Later the mat has body, and it takes real vacuum to pull water through the fibre network. After the couch the sheet rides on a felt through the press nips, but suction still has a job: keeping the felt able to take water.

Each element works best in its own window. A vacuum box fitted too early, while the sheet is still very wet, pulls fines and filler straight through the fabric. A hydrofoil fitted too late has little to work on. Many drainage complaints on older machines are not a worn element at all, but the right element in the wrong place.

ElementPosition on a FourdrinierMain driving forceTypical role
Forming boardUnder the fabric, after the breast rollGravity drainage, fabric supportSets where drainage starts and steadies the jet landing
HydrofoilsFirst part of the tableSuction pulse behind each foil bladeStrong drainage with good formation, no vacuum pump
Low vacuum boxesMiddle of the tableLow, adjustable vacuumDraws out free water as the mat thickens
High vacuum boxesEnd of the table, ahead of the couchHigher vacuum on a narrow slotRemoves bound water, sets the dry line
Suction couch rollCouch positionVacuum through a drilled shellLast forming-section dewatering, sheet transfer
Felt suction boxFelt return runVacuum slot against the feltEmpties the felt before the next nip

Forming board: the first contact with the stock

The forming board is the first stationary element the fabric rides on after the breast roll. It is a box body with a replaceable top panel, and on most machines it can be moved forwards and backwards in the machine direction. That adjustment is the point of the design: the jet has to land at the right position relative to the board, and the right position changes with grade, speed and consistency. The upstream side of that relationship, how the jet leaves the slice, is covered in the guide to the open headbox.

A board set too close to the breast roll lets the jet land on a fabric that is already draining hard, which gives a heavy, streaky edge. A board set too far downstream lets the jet land on unsupported fabric, and ripples appear in the stock pond. On a breast-roll machine the board also supports the wire while the jet settles, and a scraper can be fitted at the breast roll when the layout calls for it.

Panel materials for a forming board

Panel material is chosen around wear and friction. UHMWPE is the gentlest option, with low friction and little harm to the fabric, but it wears faster in abrasive stock. Alumina ceramic is much harder and keeps a flat surface for a long time. Zirconia ceramic is tougher and resists chipping better. Glass-crystal panels give a dense, smooth surface and can be matched to specific machines and speeds. Panels can be custom made for different paper machines, paper types and speeds.

Shop-floor check: With the machine stopped, lay a straight edge across the board panel. A hollow of even a fraction of a millimetre across the width usually explains a persistent drainage band near one edge. If the fabric track runs shiny on one side only, look at the board before blaming the fabric.
Forming board, hydrofoils

Hydrofoils: paper machine hydrofoil angles and strips

A hydrofoil looks like a plain blade the fabric slides over, but the physics is more interesting. The fabric rides on the flat leading face, and the trailing face slopes away. In the widening wedge between fabric and blade a negative pressure forms and draws water through the fabric. As the fabric leaves the foil, the water is stripped off, and the stock gets a pulse that breaks up flocs and helps formation.

That is why foils belong in the first part of the table: fast drainage without a vacuum pump, and a pulse that helps rather than hurts formation. Gentle, pulse-driven drainage retains fines better than a hard vacuum applied early, which counts for a lot on recycled and agro-residue furnish.

Three-strip, five-strip and seven-strip foils

Ceramic hydrofoils are made with three, five or seven strips. More strips means a longer, more gradual drainage action. A three-strip foil gives a short, stronger pull; a seven-strip foil spreads the dewatering over more length. Heavy, slow-draining stock on slow machines usually tolerates the stronger action. Lighter grades and faster machines, where formation is under pressure, tend toward more strips.

Angle: from 0.5° to 2.5°

The trailing-face angle is the main tuning variable. Standard angles run from 0.5° to 2.5° in steps of 0.5°, and other angles can be produced on request. A small angle is mild and disturbs the sheet least. A large angle drains harder but adds turbulence and risks pulling out fines.

Foil angleDrainage actionEffect on sheetTypical placement
0.5°–1°MildLeast disturbance, best for formationEarly in the table, fines-rich or light furnish
1.5°ModerateBalanced drainage and formationMid-table on most grades
2°–2.5°StrongMore drainage, more turbulence, fines loss riskSlow, heavy or slow-draining stock

A sensible layout does not use one angle everywhere. Gentler angles go near the board where stock is most dilute, and steeper ones follow as the mat gains consistency. Mills that move a whole row to a steeper angle chasing speed often see the wet line retreat, then formation worsen, then the change reversed.

Why ceramic is used on foils

The fabric runs over the foils at full speed and under tension, carrying fibre, filler and sometimes grit. Ceramic faces stay dimensionally stable, so the angle stays at its designed value instead of drifting as the surface erodes. A worn foil rounds off at the leading edge, stops creating a clean negative pressure, and the table slowly loses drainage with no step change an operator can point to.

Low vacuum box: drawing out free water

Once the mat has thickened and gravity and foils have removed the free water, foil pulses lose effect, and a modest controlled vacuum takes over. A low vacuum box is a sealed chamber under the fabric, connected to a vacuum source, with a slotted cover the fabric glides over. The vacuum is deliberately low, a few kilopascals, because the sheet is still delicate. Too much pulls fines and filler out, drags the fabric down onto the cover, raises drive load and leaves the underside of the sheet rougher than the top.

Single- and duo-chamber designs

Low vacuum boxes come with single or duo (two-chamber) options. A single chamber applies one level along its length. A duo chamber can run each chamber at a different level, so the sheet sees stepped vacuum, which is gentler and holds fines better than a sudden jump. A good box has a dense structure, a high surface finish, a low friction coefficient and low water absorption. The last matters more than it sounds: a cover that soaks up water swells, loses flatness and takes more power to drag the fabric over. Strong reverse dewatering capability keeps the box working as the fabric begins to clog.

Common mistake: Running every low vacuum box at the setting it was left on. Stock, speed and freeness change, and the right vacuum profile changes with them. Lower the first box by one notch and watch the wet line and the fines in the white water. Often the sheet does not notice, and the fabric does.

Tri high vacuum box: from low pressure to rapid dewatering

Near the end of the table the mat is strong enough for a real vacuum. A tri high vacuum box is a sealed structure connected to a vacuum pump. It takes the sheet from low-pressure dewatering into a zone of rapid, high-pressure dewatering, so the sheet reaches the couch firmer and the later sections have less water to remove.

Adjusting blocks at both ends of the panel set the width of the suction opening. Slot width controls the intensity and dwell of the vacuum on the sheet, and on machines that run different trims the opening can be matched to the sheet so that vacuum is not wasted on uncovered area. The adjusting blocks also carry a lubrication device that uses clean water to cut friction and extend the life of the wire. Clean is the operative word: lubrication water carrying fibre becomes an abrasive paste. Blocked nozzles show first as rising fabric drive load and a shiny stripe on the fabric track.

Vacuum elementVacuum level (industry typical)Sheet conditionMain risk if mis-set
Low vacuum boxLow, a few kPaMat forming, still very wetFines and filler loss, wire marking
High vacuum boxHigher, depending on position and gradeFirm mat approaching the dry lineFabric wear, drive load, sheet crushing
Suction couch rollHighest in the forming sectionFormed sheet ready for transferShell and seal wear, pick-up problems

Felt suction box: keeping the press felt receptive

The felt suction box sits in the press section, but it is a dewatering element in every sense. A felt carries water out of the nip; if it returns still full, the next nip has nowhere to put the water. The box draws water through the felt on its return run so the felt re-enters the nip consistently.

It follows the same philosophy as the low vacuum box: dense structure, high surface finish, low friction coefficient, low water absorption, all aimed at lengthening the actual running time of the felt. Single and duo-chamber options give stable vacuum, and the slot width is adjustable for paper type and machine speed. A slot that is too wide spreads the vacuum thin; one that is too narrow polishes the felt along the slot edges. Felt compaction, permeability and cleaning belong to the guide to the press felt.

Vacuum roll and suction couch roll

A vacuum roll has a perforated shell turning around a stationary suction box. The box covers a sector of the circumference, and seals along its edges hold the vacuum zone against the inside of the shell. Each hole picks up water in the vacuum zone and discharges it once it leaves.

The suction couch roll dewaters the sheet as the felt passes over it and improves the moisture uniformity of the sheet to the level needed for feeding it onto the felt. Uniformity matters as much as dryness: if one side pulls harder, the first press nip sees an uneven load and a cross-direction moisture streak survives to the reel.

Three things wear. Shell holes round off or clog, changing open area. Seals lose contact pressure, so air leaks into the vacuum zone and the pump compensates, leaving the gauge normal while the effective suction falls. And any cover glazes or wears. A roll that pulls less than it used to is more often a seal and hole problem than a pump problem.

Ceramic dewatering elements: where ceramic wins and where plastic still does

Ceramic surfaces are standard on foils and common on boards and box covers, but not an automatic upgrade in every position. Ceramic is hard and stable but brittle, and unforgiving of rough handling.

MaterialStrengthLimitationTypical use
UHMWPEVery low friction, fabric-friendly, easy to replaceWears faster in abrasive stockBoard panels and covers on cleaner stock
Alumina ceramicHard, long-lasting flat surfaceBrittle, needs careful installationFoils, boards and covers on abrasive stock
Zirconia ceramicTougher than alumina, resists chippingLess common, still needs careful handlingEdge-loaded or impact-prone positions
Glass crystalSmooth, dense, wear-resistantSelected case by case for machine and gradeCustom panels for speed and paper type

When a ceramic edge chips, the chip is sharp enough to slice a fabric in minutes. At each shutdown, draw a piece of nylon stocking along the leading and trailing edges; a snag means that edge must be dressed or replaced before start-up. Mixing materials in one table is normal: a softer panel under the most delicate fabric zone, ceramic where geometry and wear resistance count more.

Handling note: Lift ceramic foils onto their supports instead of sliding them, and tighten clamping hardware evenly and in steps. A strip cracked by an over-tightened bolt may show nothing at first and then fail on the first vacuum surge.

Dewatering elements on Indian paper machines: furnish, climate and machine age

Many machines running in India were laid out for one furnish and one speed, then asked to do something else. A Fourdrinier built around virgin kraft pulp now runs recycled OCC with more fines and stickies and a lower freeness. A slow, heavy-sheet machine is pushed toward lighter grades. Cylinder-mould and older Fourdrinier lines in Uttar Pradesh, Gujarat, Maharashtra, Punjab and Tamil Nadu run kraft, writing and printing, and corrugating medium on tables that have been patched for years. The result is a drainage bottleneck long before the drive or the dryers reach their limit.

How Indian furnish changes the table

Mills in India run a wide range of fibre. Recycled OCC from mixed domestic sources arrives with variable freeness and a steady load of fines and grit, which favours ceramic wearing surfaces and gentle early drainage. Bagasse and wheat-straw pulps, common where agro-residue is the most readily collected local fibre, hold water stubbornly and carry short fibre and fines; the same table that is comfortable on wood pulp behaves like a different machine. On those stocks a foil layout with gentler angles near the board and a duo-chamber low vacuum box tend to protect retention, while a hard vacuum applied early washes the fines out.

Monsoon, heat and white water

Climate shows up in the wet end more than most people expect. In the hot months, warm white water drains faster and carries more dissolved organics, so slime and deposits build in box slots and on foil edges. In the monsoon, the humid air and the warmer, more contaminated furnish make slot cleaning and shower checks a weekly job instead of a monthly one. A shiny, sour, slimy slot is a cleaning problem. A clean slot with a polished edge is a wear problem.

Reading the symptoms

SymptomLikely cause in the dewatering elementsFirst check
Wet line creeping toward the couchWorn foil edges, blocked box slots, finer stockFoil edges, box gauges, stock freeness
Cross-direction streaks or bandsUneven panel wear, clogged section of a boxStraight-edge the panels, rinse the slots
Fabric wearing early on one edgeMisaligned board or box, edge seal leakLevel and parallelism of the supports
High fabric drive loadVacuum too high, blocked lubrication, worn coversLubrication nozzles, vacuum set-point
Fines loss, dirty white waterVacuum too early, foil angle too steepFirst-box vacuum, angle near the board
Wet sheet into the press, crushingCouch seal problem, low effective vacuumSeals, hole open area, vacuum plumbing

Retrofitting an older Indian machine without rebuilding

Dewatering elements can usually be changed without touching the frame, drives or headbox. On an older machine, start where degradation is most likely: replace worn foils with ceramic foils at suitable angles, refit box covers, repair couch roll seals. That alone often recovers the original drainage. Only then consider changing the arrangement, such as adding a high vacuum box ahead of the couch or moving from single- to duo-chamber boxes.

Higher speed is where retrofitting gets serious, because the stock has less time on the table. The common error is to raise speed first and fix drainage later. Measure the wet line at current speed, restore everything below original performance, then raise speed in small steps. If the wet line runs out of room before the target, the fixed hardware has reached its capacity and the layout must change. A new foil row under an old, flattened fabric will not perform either, since the fabric becomes the limit; see the guide to the forming fabric for that side of the decision.

Selecting, installing and maintaining dewatering elements in India

Selection for an Indian mill starts with furnish and grade, not the catalogue. What is the freeness at the headbox, how fast does the machine run now and in two years, how abrasive is the stock, and does the vacuum system have capacity for another box? Then follow a sequence: decide the layout from the wet-line position, choose the wearing-surface material for each position, check the vacuum pump and piping, and set the adjustable parameters (foil angle, slot width, vacuum level, lubrication flow) as a starting point to tune on the machine.

Most early failures of new elements come from installation. Level the supports across the full width, recheck after the first week, test boxes for leaks with vacuum on and fabric off, inspect seals for twist, and flush the lubrication nozzles. After start-up, trim in the order the water leaves: board, foils, low vacuum, high vacuum, couch, felt box. Adjusting the wrong end first makes it impossible to tell what a change did.

For maintenance, elements wear slowly and fail quietly. At every shutdown, walk the table with a torch and straight edge, check edges and slot lips, and look for polished tracks under the fabric. Over longer cycles, record the vacuum at each box at fixed speed and grade, record the wet line at the same reference, and log fabric and felt changes beside element changes, because a new fabric often exposes wear the old open fabric was hiding.

Typical industry reference values

Standard hydrofoil angles0.5°, 1°, 1.5°, 2°, 2.5° (other angles on request)
Hydrofoil strip countsThree, five and seven strips
Forming board panel optionsUHMWPE, alumina ceramic, zirconia ceramic, glass crystal
Vacuum box chamber optionsSingle-chamber or duo-chamber
Low vacuum box levelA few kPa
Sheet solids after the press sectionTypically 40–50%, depending on grade and press layout
Adjustable settingsBoard position, foil angle, slot width, vacuum level, lubrication flow

Huatao Group dewatering elements for Indian paper machines

Huatao Group supplies the forming-section and press-section elements described above. The details below come from the product range, with a note on where each matters on Indian machines.

The forming board is a box body with a top panel. It can move forwards and backwards and can be adjusted to the best landing point of the slurry for good formation and dewatering, and a breast roll scraper can be installed at the board. For an Indian mill that changes between OCC-based kraft and lighter grades on the same machine, that adjustability is what lets one board serve several jets. Panels come in UHMWPE, alumina ceramic, zirconia ceramic and glass crystal, with custom panels for different machines, paper types and speeds. Alumina and zirconia suit gritty recycled stock; UHMWPE suits cleaner, lighter-grade runs.

The ceramic hydrofoils are mainly used in the forming section, in three-, five- and seven-strip versions. Standard angles are 0.5°, 1°, 1.5°, 2° and 2.5°, and any angle can be produced on request. Angle design improves both dewatering and sheet formation. On an older Indian machine, built-to-order angles let a mill fit a foil row to its actual furnish, such as bagasse or wheat-straw blends, instead of accepting whatever the original table had.

The low vacuum box has a dense structure, a high surface finish, a low friction coefficient and low water absorption, which lengthens the actual working time of the forming wire and contributes to lower energy use. It comes in single and duo-chamber versions with stable vacuum and strong reverse dewatering capability. On humid, slime-prone Indian tables, the low water absorption and smooth finish help keep the slot from fouling as quickly.

The tri high vacuum box is a sealed structure that, driven by a vacuum pump, moves the sheet from low-pressure dewatering to high-pressure rapid dewatering, which speeds up drying and improves forming. Adjusting blocks at both ends of the panel set the suction width, and the blocks carry a lubrication device that reduces friction with clean water and extends net life. This helps where machines run several sheet widths or where fabrics are changed often.

The felt suction box shares the dense, smooth, low-friction, low-water-absorption build, improves the actual working time of the felt and contributes to lower energy use. It comes in single and duo-chamber options with stable vacuum, and its slot width is adjustable for different paper types and machine speeds, so one box can follow a mill that moves between packaging and writing grades. The suction couch roll dewaters the sheet as the felt belt passes through, improving the moisture uniformity of the sheet to the extent required for felt feeding.

Frequently asked questions

In what order should dewatering elements be placed on a Fourdrinier table?
Follow the sheet's consistency. The forming board goes first, because it supports the fabric under the jet and sets where drainage begins. Hydrofoils follow, giving strong drainage and good formation without a vacuum pump. Low vacuum boxes come next, once the mat has thickened and needs a gentle pull. High vacuum boxes sit at the end of the table, ahead of the couch, where the mat can take a hard pull. The suction couch roll finishes the forming section. A high vacuum box placed early risks losing fines and filler, so position matters as much as the element itself.
What is the difference between a hydrofoil and a low vacuum box?
A hydrofoil makes its own suction. As the fabric leaves the sloping trailing face, a negative pressure forms in the wedge between fabric and blade, and water is drawn out with a pulse that also improves formation. It needs no vacuum pump. A low vacuum box is a sealed chamber connected to a vacuum source, so it applies a controlled, adjustable suction through a slotted cover. Foils work earlier, on dilute stock; low vacuum boxes take over when the sheet has more body and needs a steadier pull. Most tables use both in sequence.
Which hydrofoil angle suits a slow Indian machine running recycled board furnish?
Slow machines on heavy, slow-draining stock such as OCC-based board usually tolerate a stronger action, so angles toward the upper end of the 0.5° to 2.5° range are a reasonable start, with gentler angles near the forming board to protect formation. Indian mills should begin with a mixed layout rather than one angle across the row. Watch the wet line and the white water: if fines loss rises, ease back one step. Treat the first choice as a trial rather than a rule, because furnish and speed change the answer from one mill to the next.
Is ceramic always better than UHMWPE for forming board panels?
No. Alumina and zirconia ceramic hold a flat geometry much longer in abrasive stock, which suits filled grades and gritty recycled furnish. UHMWPE has lower friction and is gentler on the fabric but wears faster. Zirconia resists chipping better than alumina, and glass-crystal panels can be matched to speed and paper type. The right choice depends on abrasiveness, fabric sensitivity and handling practice. Many mills use more than one material across the table, softer under the most delicate fabric zone and ceramic where geometry matters more.
Why does the vacuum gauge look normal when the couch roll pulls less water?
The gauge reads vacuum in the plumbing, not effective suction at the sheet. If seals along the edges of the stationary box have worn, air leaks into the vacuum zone and the pump compensates, so the reading holds while less water moves through the shell. Clogged or rounded holes reduce open area in the same way. Stop the machine, inspect seals and shell holes, and compare the vacuum flow with an earlier record. Enlarging the pump without checking these is a common and unproductive fix, and it is seen often on older machines in India.
What does a duo-chamber vacuum box offer over a single-chamber box?
A duo-chamber box has two vacuum chambers in the machine direction, each settable to a different level, so the sheet sees stepped vacuum instead of one abrupt pull. That is gentler on a fragile sheet and helps retain fines, which matters on bagasse and wheat-straw furnish where fines are plentiful. It also gives the operator an extra adjustment. A single-chamber box is simpler and works where the stock is forgiving. Both options exist for forming-section boxes and felt suction boxes.
How does monsoon humidity affect vacuum box and foil performance in India?
Humidity itself does little to the hardware, but the warm, contaminated white water that comes with the monsoon months does. Slime and deposits build faster in box slots, on cover lips and in lubrication nozzles, so effective open area shrinks and drive load rises. Weekly slot rinsing, nozzle checks and a review of the vacuum record against earlier months help. Low water absorption and a smooth cover finish slow the fouling. A sour smell and a slimy slot point to cleaning; a clean slot with a polished edge points to wear.
How do I know if a felt suction box slot is set correctly?
Look at two things. First, felt moisture after the box: a felt still saturated at nip entry means the slot is too wide, spreading the vacuum thin, or the box is leaking. Second, the felt surface along the slot: a polished or glazed stripe suggests the slot is too narrow and the edges are working the felt too hard. Adjust the slot in small steps for the paper type and speed, then judge over a full felt cycle, because the effect on felt life only shows after weeks of running.
Can new dewatering elements raise the speed of an old Indian paper machine?
They can remove one limit, not all of them. If the wet line is creeping toward the couch, worn foils, tired box covers or failing couch seals are probably holding the machine back, and restoring them often recovers the original drainage. In India, where many lines run well below modern speeds, speed beyond the design then depends on whether the layout can remove enough water in the shorter time on the table. Measure the wet line, fix worn parts first, then raise speed in small steps. If the wet line runs out of room, add or reconfigure boxes, and check the press and dryer sections as well.